Enterasys Networks ANG-1000 manual Checking Device Status, Click the Device Status menu option

Page 40

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

Checking Device Status

The Device Status window provides a host of important data to ensure the ANG-1000 is connected properly and to permit troubleshooting as problems occur. When consulting Enterasys Customer Support, you will be asked to display this window.

The following categories are detailed in the Device Status window:

HVersion lists the Release, Patch and Build numbers, and internal name of the ANG-1000’s firmware.

HCPU itemizes Motorola Coldfire chip specifications.

HMemory enumerates ANG-1000 memory values including Total, Used, Free, Shared, Cached, Buffered and Swapped bytes.

HInterface Configuration describes Trusted (eth0), External (eth1), IPsec (eth1:0-24), PPTP (ppp0-24) and Local Loopback (lo) port data including IP and MAC addresses, netmasks, Receive and Transmit errors and other information. Note that the ppp0 interface is the Internet, not WAN interface, if the Internet is configured for PPPoE.

HNetwork Devices tabulates interface Receive and Transmit errors.

HRoute Table entries detail connected networks, gateways, their associated IP addresses, netmasks and other data.

HInterrupts lists the hardware interrupts supported on the ANG-1000 as well as their vectors and interrupt counters. The two SMC9194 items listed are the Ethernet Trusted and External port interrupts.

HSystem Log categorizes ANG-1000 functions/malfunctions including routing connections/disconnections.

Check Device Status by performing the following step:

1Click the Device Status menu option.

The Device Status window appears as shown in Figure 25.

28	Aurorean Network Gateway-1000 User’s Guide

Image 40

Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage System Description OverviewANG-1000 Front Rear ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Accessories Connecting CablesLocation Planning Connecting Cables PowerEthernet Cables ANG-3000/7000 Do one of the following as shown in FigureAurorean Network Gateway-1000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyChecking ANG-1000 Connections Rear Panel Link LEDsFront Panel LEDs Chapter Checking ANG-1000 ConnectionsPower COM1 and COM2 Leds are not operational at this timeActive InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Logging into Web Config To log into Web Config, perform the steps belowLogin window appears as shown in Figure VPN Status window appears as shown in FigureViewing VPN Status VPNClick the Firmware Upgrade menu option Firmware Upgrade window appears as shown in FigureFirmware Update window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareSetting Up the VPN Click the VPN Setup menu optionVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Internet Setup window appears as shown in Figure Click the Internet Setup menu optionDo one of the following Configuring the ANG-1000 with Aurorean Web Config Setting Up the LAN Click the LAN Setup menu optionLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Setting Up the Firewall Begin Firewall Setup by performing the following stepsClick the Firewall Setup menu option Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSetting Your Password Click the Set Password menu optionSet Password window appears as shown in Figure Set PasswordClick the Device Status menu option Checking Device StatusDevice Status window appears as shown in Figure Device Status Window Network Devices Route TableInterrupts System LogUsing Advanced Utilities Click the Advanced Utilities menu optionAdvanced Utilities window appears as shown in Figure Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Switch Arg Definition Follow the steps below to configure IP port forwardingUsage Example Page Aurorean Web Config GlossaryAurorean Network Gateway Aurorean Policy ServerEthernet FirewallInternet Service Provider ISP Generic Routing Encapsulation GREIP Address IP Security Protocol IPSecMac Address LEDsNetwork Address Translation NAT Network Administrator Point of Presence POPPoint-to-Point Protocol PPP Point-to-Point Tunneling Protocol PptpRiverMaster RoutersTunneling Virtual Private Network VPNThis appendix details the specifications of the ANG-1000 SpecificationsCategory Parameters Specifications Pin Signal Pin AssignmentsLink 1 Trusted Link 2 ExternalPin Assignments Enterasys Networks License Agreement License Agreement & SupportLicense Grant Warranty Limitation of Liability Infringement IndemnificationAppendix D International Provisions TerminationApplicable Law Government Commercial Computer Software Technical SupportSupport from Enterasys Networks Returning Products for Repair Technical SupportIndex Index POPIndex