Enterasys Networks manual Configuring the ANG-1000 with Aurorean Web Config

Page 36

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

HClick the Manual assigned IP address radio button and perform the following steps:

–Set the ANG-1000’s IP address.

–Set the Subnet mask.

–Optional. Click the DHCP server enabled box if the server is up and running.

–Set the Starting IP address of the range of consecutive IP addresses you will create for this ANG-1000.

–Set the total Number of IP addresses the ANG-1000 can distribute.

–Optional. Keep Enable DNS proxy checked so that the ANG-1000 will act as a DNS server for all its tunnels. DNS proxy resolves host names and IP addresses because the domain server is non-routable, forcing attached hosts to request these values. If your hosts know the DNS address they are seeking, you can disable this feature. This option is on by default.

–Optional. Keep Enable WINS proxy checked so that PCs on the LAN can be notified of WINS servers discovered during tunnel setup. WINS proxy notifies local PCs of the remote WINS servers without manual intervention. This option can be disabled if local PCs already know remote WINS server IP addresses. This option is on by default.

–Click Apply.

CAUTION

If you change the default LAN Setup and reboot the ANG-1000, you must release and renew the IP address for all adaptors bound to TCP/IP on your connected computer(s) in order to reconnect with the ANG-1000 and make future changes. Perform the following steps:

-On your desktop, click Start. and Run.

-For Windows 95/98/ME systems, type: winipcfg, click OK, click Release and click OK. Then click Renew All and click OK.

-For Windows NT/2000 systems, type ipconfig /release and press ENTER. Then type ipconfig /renew and press ENTER.

-For Macintosh systems, check the TCP-IP control panel.

3If you chose the DHCP option or changed the DNS or WINS default entries, a window appears detailing the reconfiguration changes and prompting you to reboot the ANG-1000. Click Reboot Now.

24	Aurorean Network Gateway-1000 User’s Guide

Image 36

Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage Overview System DescriptionANG-1000 Front Rear ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Connecting Cables AccessoriesLocation Planning Power Connecting CablesEthernet Cables Do one of the following as shown in Figure ANG-3000/7000Aurorean Network Gateway-1000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyChecking ANG-1000 Connections Rear Panel Link LEDsFront Panel LEDs Chapter Checking ANG-1000 ConnectionsPower COM1 and COM2 Leds are not operational at this timeActive InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Logging into Web Config To log into Web Config, perform the steps belowLogin window appears as shown in Figure VPN Status window appears as shown in FigureViewing VPN Status VPNClick the Firmware Upgrade menu option Firmware Upgrade window appears as shown in FigureFirmware Update window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareSetting Up the VPN Click the VPN Setup menu optionVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Click the Internet Setup menu option Internet Setup window appears as shown in FigureDo one of the following Configuring the ANG-1000 with Aurorean Web Config Setting Up the LAN Click the LAN Setup menu optionLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Setting Up the Firewall Begin Firewall Setup by performing the following stepsClick the Firewall Setup menu option Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSetting Your Password Click the Set Password menu optionSet Password window appears as shown in Figure Set PasswordChecking Device Status Click the Device Status menu optionDevice Status window appears as shown in Figure Device Status Window Network Devices Route TableInterrupts System LogUsing Advanced Utilities Click the Advanced Utilities menu optionAdvanced Utilities window appears as shown in Figure Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Follow the steps below to configure IP port forwarding Switch Arg DefinitionUsage Example Page Aurorean Web Config GlossaryAurorean Network Gateway Aurorean Policy ServerEthernet FirewallInternet Service Provider ISP Generic Routing Encapsulation GREIP Address IP Security Protocol IPSecLEDs Mac AddressNetwork Address Translation NAT Network Administrator Point of Presence POPPoint-to-Point Protocol PPP Point-to-Point Tunneling Protocol PptpRiverMaster RoutersTunneling Virtual Private Network VPNSpecifications This appendix details the specifications of the ANG-1000Category Parameters Specifications Pin Signal Pin AssignmentsLink 1 Trusted Link 2 ExternalPin Assignments License Agreement & Support Enterasys Networks License AgreementLicense Grant Warranty Infringement Indemnification Limitation of LiabilityAppendix D Termination International ProvisionsApplicable Law Technical Support Government Commercial Computer SoftwareSupport from Enterasys Networks Returning Products for Repair Technical SupportIndex Index POPIndex