Enterasys Networks ANG-1000 manual Setting Up the VPN, Click the VPN Setup menu option

Page 30

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

Setting Up the VPN

The VPN configuration created on the ANG-1000 completes a link with the ANG-3000/7000 on the remote end of this connection. If your network administrator has already set up the ANG-3000/7000 with appropriate User, Password and Group information, after setting up the VPN you will build the site-to-site tunnel connection and be up and running on the corporate LAN.

Begin VPN Setup by performing the following steps:

1Click the VPN Setup menu option.

The VPN Setup window appears as shown in Figure 20.

Help

VPN

VPN Status

VPN Setup

Connectivity Setup

Internet Setup

LAN Setup

Firewall Setup

ANG-1000 System

Set Password

Device Status

Firmware Update

Advanced Utilities

Links

Config File Editor

Aurorean Products

Enterasys Home

Aurorean Network Gateway 1000

VPN Setup

Assigned VPN Connections:

There are no network gateway connections currently defined. Please fill in the information below and add one.

Add VPN Connection:

Name:

Gateway:

Username:

Password:

Confirm:

EZ-IPsec(uses EZ-IPSec™auto-configuration)

Connection type:

PPTP

Start network gateway now:

Apply

Global VPN Settings:

Force default route (single VPN only): disabled

Apply

Figure 20 VPN Setup Window

18

Aurorean Network Gateway-1000 User’s Guide

Image 30
Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage Overview System DescriptionANG-1000 Front Rear ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Connecting Cables AccessoriesLocation Planning Power Connecting CablesEthernet Cables Do one of the following as shown in Figure ANG-3000/7000Aurorean Network Gateway-1000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyFront Panel LEDs Checking ANG-1000 ConnectionsRear Panel Link LEDs Chapter Checking ANG-1000 ConnectionsActive PowerCOM1 and COM2 Leds are not operational at this time InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Login window appears as shown in Figure Logging into Web ConfigTo log into Web Config, perform the steps below VPN Status window appears as shown in FigureViewing VPN Status VPNFirmware Update window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Upgrade window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareVPN Setup window appears as shown in Figure Setting Up the VPNClick the VPN Setup menu option Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Click the Internet Setup menu option Internet Setup window appears as shown in FigureDo one of the following Configuring the ANG-1000 with Aurorean Web Config LAN Setup window appears as shown in Figure Setting Up the LANClick the LAN Setup menu option LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Click the Firewall Setup menu option Setting Up the FirewallBegin Firewall Setup by performing the following steps Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSet Password window appears as shown in Figure Setting Your PasswordClick the Set Password menu option Set PasswordChecking Device Status Click the Device Status menu optionDevice Status window appears as shown in Figure Device Status Window Interrupts Network DevicesRoute Table System LogAdvanced Utilities window appears as shown in Figure Using Advanced UtilitiesClick the Advanced Utilities menu option Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Follow the steps below to configure IP port forwarding Switch Arg DefinitionUsage Example Page Aurorean Network Gateway Aurorean Web ConfigGlossary Aurorean Policy ServerEthernet FirewallIP Address Internet Service Provider ISPGeneric Routing Encapsulation GRE IP Security Protocol IPSecLEDs Mac AddressNetwork Address Translation NAT Point-to-Point Protocol PPP Network AdministratorPoint of Presence POP Point-to-Point Tunneling Protocol PptpTunneling RiverMasterRouters Virtual Private Network VPNSpecifications This appendix details the specifications of the ANG-1000Category Parameters Specifications Link 1 Trusted Pin SignalPin Assignments Link 2 ExternalPin Assignments License Agreement & Support Enterasys Networks License AgreementLicense Grant Warranty Infringement Indemnification Limitation of LiabilityAppendix D Termination International ProvisionsApplicable Law Technical Support Government Commercial Computer SoftwareSupport from Enterasys Networks Returning Products for Repair Technical SupportIndex Index POPIndex