Enterasys Networks ANG-1100 manual Checking ANG-1102/1105 Connections, LED behavior

Page 22

Checking ANG-1102/1105 Connections	Chapter 2
	Installation

Checking ANG-1102/1105 Connections

The ANG-1100 is now connected and ready for configuration. Check the LEDS in the manner described below to confirm that the connections are working properly.

LED behavior

The LEDs behave as follows at when powered up at startup:

!Power LED stays ON for 2-3 seconds indicating boot diagnostics are running followed by boot up of the Linux kernel.

–If the Power LED flashes at a twice per second interval, boot diagnostics have failed.

–If the Power LED remains ON or OFF following the boot sequence, the kernel has failed to boot.

!Power LED blinks once per second indicating the system is operating correctly.

!LAN LEDs 1-4 either blink when active or remain ON. The ANG-1102 LAN LEDs are amber (10 Mbps); the ANG-1105 LAN LEDs are green (100 Mbps) or amber if the connected device is running at 10 Mbps.

!The WAN LED either blinks when active or remains ON.

!The VPN LED stays ON when a tunnel is connected.

The ANG-1100 is now ready for configuration. Refer to Chapter 3 for detailed instructions.

10	Aurorean Network Gateway-1100 User’s Guide

Image 22

Contents ANG-1100 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1100 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1100 with Aurorean Web Table of ContentsUnited States Government Restricted Rights Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage Overview System DescriptionANG-1102/1105 Topology System DescriptionInstallation Unpacking the ANG-1102/1105Location Planning AccessoriesUnpacking the ANG-1102/1105 Chapter Connecting Cables Connecting CablesEthernet Connections ANG-3000/7000 Do one of the following as shown in FigureAurorean Network Reset TER NAL Serial ConnectionConnecting Power to the ANG-1102/1105 Connecting Power to the ANG-1102/1105 ChapterConnecting the Power Cable to the Power Supply Connecting Power to the ANG-1102/1105LED behavior Checking ANG-1102/1105 ConnectionsChecking ANG-1102/1105 Connections Chapter Configuring the ANG-1100 with Aurorean Web Config Before You BeginConfiguring the ANG-1100 with Aurorean Web Config Login window appears as shown in Figure Logging into Web ConfigTo log into Web Config, perform the steps below VPN Status window appears as shown in FigureSet Password window appears as shown in Figure Setting Your PasswordClick the Set Password menu option Set PasswordViewing VPN Status VPN StatusClick the VPN Setup menu option Setting Up the VPNVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN Setup Assigned VPN ConnectionsSelect one of the following Connection modes Click Apply Click the Internet Setup menu option Setting Up the Internet ConnectionInternet Setup window appears as shown in Figure Internet Setup Window Do one of the following Internet SetupConfiguring the ANG-1100 with Aurorean Web Config Firmware Update window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Upgrade window appears as shown in Figure Firmware UpdateSecond Firmware Update Window Aurorean Network Gateway Firmware Update Image Date and Build InformationLAN Setup window appears as shown in Figure Setting Up the LANClick the LAN Setup menu option LAN SetupConfiguring the ANG-1100 with Aurorean Web Config Setting Up the Firewall Firewall Setup window appears as shown in Figure Begin Firewall Setup by performing the following stepsClick the Firewall Setup menu option Firewall SetupSetting Your Password Set Password Window Click the Device Status menu option Checking Device StatusDevice Status window appears as shown in Figure Device Status Window Interrupts Network DevicesRoute Table System LogAdvanced Utilities window appears as shown in Figure Using Advanced UtilitiesAdvanced Utilities Using the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureConfiguring the ANG-1100 with Aurorean Web Config Configuring IP Port Forwarding Switch Arg Definition Follow the steps below to configure IP port forwardingUsage Example Page Aurorean Network Gateway Aurorean Web ConfigGlossary Aurorean Policy ServerEthernet FirewallIP Address Internet Service Provider ISPGeneric Routing Encapsulation GRE IP Security Protocol IPSecLEDs Network Address Translation NAT Network AdministratorMac Address Point-to-Point Tunneling Protocol Pptp Point of Presence POPPoint-to-Point Protocol PPP PPPoETunneling RoutersVirtual Private Network VPN This appendix details the specifications of the ANG-1100 SpecificationsCategory Parameters Specifications Vcci Page Pin Assignments Pin Signal Ethernet Port Pin AssignmentsDB-9 Serial Port Pin AssignmentsPage Program License Agreement Support Enterasys Networks, Inc. Program License AgreementApplicable Law LicenseOther Restrictions Export RequirementsUnited States Government Restricted Rights Exclusion of WarrantyUnited States Government Restricted Rights Technical Support No Liability for Consequential DamagesSupport from Enterasys Networks Returning Products for Repair Technical SupportPage Index VPN LEDIndex LANPOP Index