Enterasys Networks ANG-1100 manual Checking Device Status, Click the Device Status menu option

Page 44

Chapter 3

Configuring the ANG-1100 with Aurorean Web Config

Checking Device Status

The Device Status window provides a host of important data to ensure the ANG-1100 is connected properly and to permit troubleshooting as problems occur. When consulting Enterasys Customer Support, you will be asked to display this window.

The following categories are detailed in the Device Status window:

!Version lists the Release, Patch and Build numbers, and internal name of the ANG-1100’s firmware.

!CPU itemizes Motorola Coldfire chip specifications.

!Memory enumerates ANG-1100 memory values including Total, Used, Free, Shared, Cached, Buffered and Swapped bytes.

!Interface Configuration describes Trusted (eth0), External (eth1), IPsec (eth1:0-24), PPTP (ppp0-24) and Local Loopback (lo) port data including IP and MAC addresses, netmasks, Receive and Transmit errors and other information. Note that the ppp0 interface is the Internet, not WAN interface, if the Internet is configured for PPPoE.

!Network Devices tabulates interface Receive and Transmit errors.

!Route Table entries detail connected networks, gateways, their associated IP addresses, netmasks and other data.

!Interrupts lists the hardware interrupts supported on the ANG-1100 as well as their vectors and interrupt counters. The two SMC9194 items listed are the Ethernet Trusted and External port interrupts.

!System Log categorizes ANG-1100 functions/malfunctions including routing connections/disconnections.

Check Device Status by performing the following step:

1Click the Device Status menu option.

The Device Status window appears as shown in Figure 23.

32

Aurorean Network Gateway-1100 User’s Guide

Image 44
Contents ANG-1100 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1100 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1100 with Aurorean Web Table of ContentsUnited States Government Restricted Rights Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage Overview System DescriptionANG-1102/1105 Topology System DescriptionInstallation Unpacking the ANG-1102/1105Unpacking the ANG-1102/1105 Chapter AccessoriesLocation Planning Ethernet Connections Connecting CablesConnecting Cables Aurorean Network Do one of the following as shown in FigureANG-3000/7000 Reset TER NAL Serial ConnectionConnecting Power to the ANG-1102/1105 Connecting Power to the ANG-1102/1105 ChapterConnecting the Power Cable to the Power Supply Connecting Power to the ANG-1102/1105Checking ANG-1102/1105 Connections Chapter Checking ANG-1102/1105 ConnectionsLED behavior Configuring the ANG-1100 with Aurorean Web Config Before You BeginConfiguring the ANG-1100 with Aurorean Web Config Logging into Web Config To log into Web Config, perform the steps belowLogin window appears as shown in Figure VPN Status window appears as shown in FigureSetting Your Password Click the Set Password menu optionSet Password window appears as shown in Figure Set PasswordViewing VPN Status VPN StatusVPN Setup window appears as shown in Figure Setting Up the VPNClick the VPN Setup menu option Aurorean Network Gateway VPN Setup Assigned VPN ConnectionsSelect one of the following Connection modes Click Apply Internet Setup window appears as shown in Figure Setting Up the Internet ConnectionClick the Internet Setup menu option Internet Setup Window Do one of the following Internet SetupConfiguring the ANG-1100 with Aurorean Web Config Click the Firmware Upgrade menu option Firmware Upgrade window appears as shown in FigureFirmware Update window appears as shown in Figure Firmware UpdateSecond Firmware Update Window Aurorean Network Gateway Firmware Update Image Date and Build InformationSetting Up the LAN Click the LAN Setup menu optionLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1100 with Aurorean Web Config Setting Up the Firewall Begin Firewall Setup by performing the following steps Click the Firewall Setup menu optionFirewall Setup window appears as shown in Figure Firewall SetupSetting Your Password Set Password Window Device Status window appears as shown in Figure Checking Device StatusClick the Device Status menu option Device Status Window Network Devices Route TableInterrupts System LogAdvanced Utilities Using Advanced UtilitiesAdvanced Utilities window appears as shown in Figure Using the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureConfiguring the ANG-1100 with Aurorean Web Config Configuring IP Port Forwarding Usage Follow the steps below to configure IP port forwardingSwitch Arg Definition Example Page Aurorean Web Config GlossaryAurorean Network Gateway Aurorean Policy ServerEthernet FirewallInternet Service Provider ISP Generic Routing Encapsulation GREIP Address IP Security Protocol IPSecMac Address Network Address Translation NAT Network AdministratorLEDs Point of Presence POP Point-to-Point Protocol PPPPoint-to-Point Tunneling Protocol Pptp PPPoEVirtual Private Network VPN RoutersTunneling Category Parameters SpecificationsThis appendix details the specifications of the ANG-1100 Specifications Vcci Page Pin Assignments Pin Signal Ethernet Port Pin AssignmentsDB-9 Serial Port Pin AssignmentsPage Program License Agreement Support Enterasys Networks, Inc. Program License AgreementLicense Other RestrictionsApplicable Law Export RequirementsUnited States Government Restricted Rights Exclusion of WarrantyUnited States Government Restricted Rights Support from Enterasys Networks No Liability for Consequential DamagesTechnical Support Returning Products for Repair Technical SupportPage Index VPN LEDIndex LANPOP Index