Enterasys Networks ANG-1100 manual Connecting Cables, Ethernet Connections

Page 17

Chapter 2	Connecting Cables
Installation

Connecting Cables

Ethernet cables are used to connect the ANG-1100 to your computer or LAN and the Internet. A serial cable can be used to connect the ANG-1105 to your computer for diagnostic purposes.

All interconnections are made at the back of the ANG-1100 (refer to Figure 5). Also, a reset button is located in the rear of the unit.

CAUTION

If you press the Reset button after you have configured your ANG-1100, you will lose your entire configuration. Any settings you supplied must then be re-entered. Do not use the Reset button unless you want the configuration to return to factory defaults; you may want to record your settings before using the Reset button.

Ethernet Connections

The ANG-1102 is equipped with two 8-pin modular RJ-45 Ethernet ports (five ports on the ANG-1105) labeled TRUSTED and EXTERNAL as shown in Figure 5. The trusted port is connected to a computer or hub/switch with networked computers. The external port is connected to a cable or DSL

modem.
PO
W
E	CO
R	CO	RE
	M	RE
		SET	E
			XTE
			R
			N	1
			AL	1	2	3
					2		4
					T
					T
					RU
						STE
						D

Figure 5 Location of the Serial/WAN/LAN Ports (ANG-1105 shown)

The trusted connection can be either a sole desktop computer or a hub that connects up to 25 tunnels to the network as shown in Figure 6.

Aurorean Network Gateway-1100 User’s Guide

5

Image 17

Contents Aurorean Virtual Network ANG-1100 User’s GuideAurorean Network Gateway-1100 User’s Guide Iii Important Safety Instructions Table of Contents Table of Contents Configuring the ANG-1100 with Aurorean WebUnited States Government Restricted Rights Page About This Guide Contents of the GuideConventions Used in This Guide About This Guide Related Publications Related PublicationsPage System Description OverviewSystem Description ANG-1102/1105 TopologyUnpacking the ANG-1102/1105 InstallationUnpacking the ANG-1102/1105 Chapter AccessoriesLocation Planning Ethernet Connections Connecting CablesConnecting Cables Aurorean Network Do one of the following as shown in FigureANG-3000/7000 Serial Connection Reset TER NALConnecting Power to the ANG-1102/1105 Chapter Connecting Power to the ANG-1102/1105Connecting Power to the ANG-1102/1105 Connecting the Power Cable to the Power SupplyChecking ANG-1102/1105 Connections Chapter Checking ANG-1102/1105 ConnectionsLED behavior Before You Begin Configuring the ANG-1100 with Aurorean Web ConfigConfiguring the ANG-1100 with Aurorean Web Config To log into Web Config, perform the steps below Logging into Web ConfigLogin window appears as shown in Figure VPN Status window appears as shown in FigureClick the Set Password menu option Setting Your PasswordSet Password window appears as shown in Figure Set PasswordVPN Status Viewing VPN StatusVPN Setup window appears as shown in Figure Setting Up the VPNClick the VPN Setup menu option Assigned VPN Connections Aurorean Network Gateway VPN SetupSelect one of the following Connection modes Click Apply Internet Setup window appears as shown in Figure Setting Up the Internet ConnectionClick the Internet Setup menu option Internet Setup Internet Setup Window Do one of the followingConfiguring the ANG-1100 with Aurorean Web Config Firmware Upgrade window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Update window appears as shown in Figure Firmware UpdateSecond Firmware Update Window Image Date and Build Information Aurorean Network Gateway Firmware UpdateClick the LAN Setup menu option Setting Up the LANLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1100 with Aurorean Web Config Setting Up the Firewall Click the Firewall Setup menu option Begin Firewall Setup by performing the following stepsFirewall Setup window appears as shown in Figure Firewall SetupSetting Your Password Set Password Window Device Status window appears as shown in Figure Checking Device StatusClick the Device Status menu option Device Status Window Route Table Network DevicesInterrupts System LogAdvanced Utilities Using Advanced UtilitiesAdvanced Utilities window appears as shown in Figure Using the Configuration Editor Configuration Edit window appears as shown in Figure Click the Configuration Edit menu optionConfiguring the ANG-1100 with Aurorean Web Config Configuring IP Port Forwarding Usage Follow the steps below to configure IP port forwardingSwitch Arg Definition Example Page Glossary Aurorean Web ConfigAurorean Network Gateway Aurorean Policy ServerFirewall EthernetGeneric Routing Encapsulation GRE Internet Service Provider ISPIP Address IP Security Protocol IPSecMac Address Network Address Translation NAT Network AdministratorLEDs Point-to-Point Protocol PPP Point of Presence POPPoint-to-Point Tunneling Protocol Pptp PPPoEVirtual Private Network VPN RoutersTunneling Category Parameters SpecificationsThis appendix details the specifications of the ANG-1100 Specifications Vcci Page Pin Assignments Ethernet Port Pin Assignments Pin SignalSerial Port Pin Assignments DB-9Page Enterasys Networks, Inc. Program License Agreement Program License Agreement SupportOther Restrictions LicenseApplicable Law Export RequirementsUnited States Government Restricted Rights Exclusion of WarrantyUnited States Government Restricted Rights Support from Enterasys Networks No Liability for Consequential DamagesTechnical Support Technical Support Returning Products for RepairPage VPN LED IndexLAN IndexPOP Index