Enterasys Networks VH-2402S manual Viewing the Current Port Configuration, Port Information

Page 38

Viewing the Current Port Configuration

The Port Information screen displays the port type, status, link state, and flow control in use, as well as the communication speed and duplex mode. To change any of the port settings, use the Port Configuration menu. The parameters shown in the following figure and table are for the RJ-45 ports.

 

 

 

--Vertical Horizon Local Management VH-2402S

 

 

 

 

 

 

Port Information : Unit 1 Port 1-12

 

 

 

Port

 

Type

Operational Link

FlowControl

Speed and

 

 

 

 

 

 

 

InUse

Duplex InUse

 

 

-------------------------------------------------------------------------------------------------------

 

 

1.

10/100TX

YES

DOWN

-----------------

----------------

 

 

2.

10/100TX

YES

DOWN

-----------------

----------------

 

 

3.

10/100TX

YES

UP

802.3x

100-FULL

 

 

4.

10/100TX

YES

DOWN

-----------------

----------------

 

 

5.

10/100TX

YES

DOWN

-----------------

----------------

 

 

6.

10/100TX

YES

UP

NONE

100-HALF

 

 

7.

10/100TX

YES

UP

802.3x

100-FULL

 

 

8.

10/100TX

YES

UP

BACK_PRESSURE 10-FULL

 

 

9.

10/100TX

YES

UP

BACK_PRESSURE 10-FULL

 

 

10.

10/100TX

YES

UP

BACK_PRESSURE 10-FULL

 

 

11.

10/100TX

YES

UP

BACK_PRESSURE 10-FULL

 

 

12.

10/100TX

YES

UP

BACK_PRESSURE 10-FULL

 

 

<OK> <PREV Unit> <NEXT UNIT> <PREV PAGE> <NEXT PAGE>

 

 

 

 

Use <TAB> or arrows keys to move. <Enter> to select.

 

 

 

 

 

 

 

 

 

 

Figure 2-21. Port Information

 

 

 

 

 

 

 

 

Parameter

 

Description

 

 

 

Type

 

Shows port type as:

 

 

 

 

 

 

10/100TX

: 10Base-T / 100Base-TX

 

 

 

 

 

100FX

: 100Base-FX

 

 

 

 

 

1000SX : 1000Base-SX

 

 

 

 

 

1000LX

: 1000Base-LX

 

 

Operational

 

Shows if the port is functioning or not.

 

 

Link

 

Indicates if the port has a valid connection to an external device.

FlowControl InUse

Shows the flow control type in use. Flow control can eliminate

 

 

 

frame loss by “blocking” traffic from end stations connected

 

 

 

directly to the switch. Back pressure is used for half duplex and

 

 

 

IEEE 802.3x for full duplex. Note that flow control should not be

 

 

 

used if a port is connected to a hub.

 

 

Speed and

 

Displays the current port speed and duplex mode used.

DuplexInUse

 

 

 

 

 

 

 

30 VH-2402S User Interface

VH-2402S

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Fast Ethernet Switch Management GuidePage 9033645-01 9033645-01 Table of Contents Snmp Management Appendix A. Spanning Tree ConceptsIndex Vi Table of Contents VH-2402S Required Connections Configuration OptionsManagement Overview Console Port Out-of-Band ConnectionsRemote Management via the Console Port Configure the Switch SiteConfigure the Remote Site In-Band ConnectionsIn-Band Network Connection Management Overview VH-2402S VH-2402S User Interface OverviewUser Access Factory Defaults Factory Default SettingsGvrp Main Menu Selection DescriptionDisplays/configures extended bridge capabilities provided by System Information Menu System Information MenuDisplaying System Information System InformationDisplaying Switch Version and Module Information Switch InformationManagement Setup Menu Management Setup MenuChanging the Network Configuration Network ConfigurationIP Configuration IP ConfigurationIP Connectivity Test Ping IP Connectivity TestHttp Configuration 10. Http ConfigurationConfiguring the Serial Port 11. Serial Port Configuration12. Snmp Configuration Assigning Snmp ParametersConfiguring Community Names 13. Snmp CommunitiesConfiguring IP Trap Managers 14. IP Trap ManagersConsole Login Configuration 15. Console Login ConfigurationUsing Tftp Protocol to Download Over the Network Downloading System SoftwareSaving the System Configuration Parameter DescriptionConfiguring Management Access 18. Management ConfigurationConfiguring the Switch 19. Device Control MenuNot implemented in the current firmware release Configuring Port Parameters 20. Port ConfigurationViewing the Current Port Configuration 21. Port InformationUsing the Spanning Tree Algorithm 22. Spanning Tree Configuration Configuring Bridge STADevice with the lowest MAC address will then Configuring STA for Ports or Modules 24. Spanning Tree Port ConfigurationViewing the Current Spanning Tree Configuration 25. Spanning Tree InformationDisplaying the Current Bridge STA 26. Bridge STA InformationDisplaying the Current STA for Ports or Modules 27. Spanning Tree Port InformationRules defining port status are Using a Mirror Port for Analysis 28. Mirror Port ConfigurationConfiguring Port Trunks 29. Port Trunking Configuration Igmp Multicast Filtering Configuring Igmp 30. Igmp ConfigurationConfiguring Broadcast Storm Control 31. Broadcast Storm Control ConfigurationConfiguring Bridge MIB Extensions 32. Extended Bridge ConfigurationBy setting this parameter to False Configuring Traffic Classes 33 .1P ConfigurationPort Priority Configuration 34 .1P Port Priority Configuration802.1P Port Traffic Class Information 35 .1P Port Traffic Class InformationConfiguring Virtual LANs 802.1Q Vlan Base Information802.1Q Vlan Current Table Information 37 .1Q Vlan Current Table Information802.1Q Vlan Static Table Configuration 38 .1Q Vlan Static Table Configuration39 .1Q Vlan Static Table Configuration Example Port Assignment Vlan Configuration 40. Port Assignment Vlan ConfigurationMulticast Router Port Information 41. Multicast Router Port InformationStatic Multicast Router Port Configuration 42. Static Multicast Router Port ConfigurationIgmp Member Port Configuration 43. Igmp Member Port ConfigurationPort Security Configuration 44. Port Security ConfigurationMonitoring the Switch 45. Network Monitor MenuDisplaying Port Statistics 46. Port StatisticsDisplaying Rmon Statistics 47. Rmon StatisticsDrop Events Displaying the Unicast Address Table 48. Unicast Address TableDisplaying the IP Multicast Registration Table 49. IP Multicast Registration TableConfiguring Static Unicast Addresses 50. Static Unicast Addreeess Table ConfigurationResetting the System Logging Off the System66 VH-2402S User Interface Configuring & Monitoring the Switch Common TasksSetting Password Protection Assigning an IP Address Checking Network Configuration StatusConnecting via Telnet Setting Snmp Management Access Viewing Switch StatisticsConfiguring Port Mirroring Downloading a Software UpgradeDownloading Via the Serial Port Downloading Via Tftp9033645-01 Configuring Spanning Tree Parameters Configuring VLANs Configuring Class of ServiceConfiguring Port Operation Configuring the Unicast Address Table Setting a Default Gateway Configuring BootPConfiguring Port Trunks Configuring & Monitoring the Switch VH-2402S Snmp Management Snmp ProtocolMIB Objects RFC 1643 Ethernet-Like MIB RFC 1213 MIB-IIRFC 1573 Interfaces Evolution MIB RFC 1493 Bridge MIBEnterasys Proprietary MIB Extensions Compiling MIB Extensions Enterasys WebsiteIeee 802.1Q Q-MIB General Spanning Tree FeaturesAppendix A. Spanning Tree Concepts Figure A-1. Spanning Tree Using VH-2402S Switches Spanning Tree Protocol in a NetworkTable A-1. Spanning Tree Protocol Defaults Spanning Tree Protocol ParametersSpanning Tree Protocol Operation 9033645-01 Spanning Tree Concepts VH-2402S Appendix B. Virtual Lans Vlans VLANs and Frame TaggingVlan Classification VH-2402S Vlan ConfigurationAssigning Ports to VLANs Port OverlappingForwarding Tagged/Untagged Frames Automatic Vlan RegistrationForwarding Traffic with Unknown Vlan Tags Appendix C. Class of Service Incoming tagged frames contain a priority level rangeFigure C-1. Class of Service Example Appendix D. IP Multicast Filtering Igmp Snooping and IP Multicast FilteringPage Index Tftp Page 150524-103 R02
Top Page Image Contents