Enterasys Networks VH-2402S manual Downloading Via the Serial Port, Downloading Via Tftp

Page 80

Downloading Via the Serial Port

A serial download is the easiest method to upgrade the VH-2402S switch software, requiring the least amount of equipment and configuration.

To download switch software via the serial port, do the following:

1.With the console port connected, reset the switch by powering the switch off and then on.

2.After the power-on hardware and software tests are complete, the system initialization screen displays the following message:.

(D)ownload System Image or (S)tart Application: [S]

3.Press “D” to download system firmware. The following message appears:

Select the Firmware Type to Download (1)Runtime (2)POST (3)Mainboard [1]:

4.Select “1” to download the agent software. The following messages appear:

Your Selection: Runtime Code

Download code to FlashROM address 0x02880000

Change Baud Rate to 115200 and Press <ENTER> to Download.

5.Change your baud rate to 115200 bps and press [Enter]. Send the file using the XMODEM protocol from your computer application (the procedure varies depending upon the application used).

When the XMODEM procedure finishes, the following messages are displayed:

XModem Download to DRAM buffer area 0x00200000: ...

SUCCESS !

Verifying image in DRAM download buffer 0x00200000... SUCCESS !

Update FlashROM Image at 0x02880000 ... SUCCESS !

(D)ownload another Image or (S)tart Application: [S] s

Change Baud Rate to 19200 and Press <ENTER>.

6.Press “S” to start the user interface, change your baud rate to back to 19200 bps and press [Enter]. The user interface logon screen will then appear.

Downloading Via TFTP

To perform a TFTP download, you must first configure the VH-2402S switch. This consists of programming the switch with an IP address, if this has not already been done, and entering the IP address of the TFTP

72 Configuring & Monitoring the Switch

VH-2402S

Image 80

Contents Fast Ethernet Switch Management GuidePage 9033645-01 9033645-01 Table of Contents Snmp Management Appendix A. Spanning Tree ConceptsIndex Vi Table of Contents VH-2402S Configuration Options Management OverviewRequired Connections Console Port Out-of-Band ConnectionsConfigure the Switch Site Configure the Remote SiteRemote Management via the Console Port In-Band ConnectionsIn-Band Network Connection Management Overview VH-2402S VH-2402S User Interface OverviewUser Access Factory Defaults Factory Default SettingsGvrp Main Menu Selection DescriptionDisplays/configures extended bridge capabilities provided by System Information Menu System Information MenuDisplaying System Information System InformationDisplaying Switch Version and Module Information Switch InformationManagement Setup Menu Management Setup MenuChanging the Network Configuration Network ConfigurationIP Configuration IP ConfigurationIP Connectivity Test Ping IP Connectivity TestHttp Configuration 10. Http ConfigurationConfiguring the Serial Port 11. Serial Port Configuration12. Snmp Configuration Assigning Snmp ParametersConfiguring Community Names 13. Snmp CommunitiesConfiguring IP Trap Managers 14. IP Trap ManagersConsole Login Configuration 15. Console Login ConfigurationUsing Tftp Protocol to Download Over the Network Downloading System SoftwareSaving the System Configuration Parameter DescriptionConfiguring Management Access 18. Management ConfigurationConfiguring the Switch 19. Device Control MenuNot implemented in the current firmware release Configuring Port Parameters 20. Port ConfigurationViewing the Current Port Configuration 21. Port InformationUsing the Spanning Tree Algorithm 22. Spanning Tree Configuration Configuring Bridge STADevice with the lowest MAC address will then Configuring STA for Ports or Modules 24. Spanning Tree Port ConfigurationViewing the Current Spanning Tree Configuration 25. Spanning Tree InformationDisplaying the Current Bridge STA 26. Bridge STA InformationDisplaying the Current STA for Ports or Modules 27. Spanning Tree Port InformationRules defining port status are Using a Mirror Port for Analysis 28. Mirror Port ConfigurationConfiguring Port Trunks 29. Port Trunking Configuration Igmp Multicast Filtering Configuring Igmp 30. Igmp ConfigurationConfiguring Broadcast Storm Control 31. Broadcast Storm Control ConfigurationConfiguring Bridge MIB Extensions 32. Extended Bridge ConfigurationBy setting this parameter to False Configuring Traffic Classes 33 .1P ConfigurationPort Priority Configuration 34 .1P Port Priority Configuration802.1P Port Traffic Class Information 35 .1P Port Traffic Class InformationConfiguring Virtual LANs 802.1Q Vlan Base Information802.1Q Vlan Current Table Information 37 .1Q Vlan Current Table Information802.1Q Vlan Static Table Configuration 38 .1Q Vlan Static Table Configuration39 .1Q Vlan Static Table Configuration Example Port Assignment Vlan Configuration 40. Port Assignment Vlan ConfigurationMulticast Router Port Information 41. Multicast Router Port InformationStatic Multicast Router Port Configuration 42. Static Multicast Router Port ConfigurationIgmp Member Port Configuration 43. Igmp Member Port ConfigurationPort Security Configuration 44. Port Security ConfigurationMonitoring the Switch 45. Network Monitor MenuDisplaying Port Statistics 46. Port StatisticsDisplaying Rmon Statistics 47. Rmon StatisticsDrop Events Displaying the Unicast Address Table 48. Unicast Address TableDisplaying the IP Multicast Registration Table 49. IP Multicast Registration TableConfiguring Static Unicast Addresses 50. Static Unicast Addreeess Table ConfigurationResetting the System Logging Off the System66 VH-2402S User Interface Configuring & Monitoring the Switch Common TasksSetting Password Protection Assigning an IP Address Checking Network Configuration StatusConnecting via Telnet Setting Snmp Management Access Viewing Switch StatisticsConfiguring Port Mirroring Downloading a Software UpgradeDownloading Via the Serial Port Downloading Via Tftp9033645-01 Configuring Spanning Tree Parameters Configuring VLANs Configuring Class of ServiceConfiguring Port Operation Configuring the Unicast Address Table Setting a Default Gateway Configuring BootPConfiguring Port Trunks Configuring & Monitoring the Switch VH-2402S Snmp Management Snmp ProtocolMIB Objects RFC 1213 MIB-II RFC 1573 Interfaces Evolution MIBRFC 1643 Ethernet-Like MIB RFC 1493 Bridge MIBEnterasys Proprietary MIB Extensions Compiling MIB Extensions Enterasys WebsiteIeee 802.1Q Q-MIB General Spanning Tree FeaturesAppendix A. Spanning Tree Concepts Figure A-1. Spanning Tree Using VH-2402S Switches Spanning Tree Protocol in a NetworkTable A-1. Spanning Tree Protocol Defaults Spanning Tree Protocol ParametersSpanning Tree Protocol Operation 9033645-01 Spanning Tree Concepts VH-2402S Appendix B. Virtual Lans Vlans VLANs and Frame TaggingVH-2402S Vlan Configuration Assigning Ports to VLANsVlan Classification Port OverlappingForwarding Tagged/Untagged Frames Automatic Vlan RegistrationForwarding Traffic with Unknown Vlan Tags Appendix C. Class of Service Incoming tagged frames contain a priority level rangeFigure C-1. Class of Service Example Appendix D. IP Multicast Filtering Igmp Snooping and IP Multicast FilteringPage Index Tftp Page 150524-103 R02