Enterasys Networks VH-2402S manual Configuring the Serial Port, Serial Port Configuration

Page 27

Configuring the Serial Port

You can access the on-board configuration program by attaching a VT100 compatible device to the switch’s serial port. (For more information on connecting to this port, see “Required Connections” on page 1.) The communication parameters for this port can be accessed from the Serial Port Configuration screen shown below and described in the following table.

Vertical Horizon Local Management -- VH-2402S

 

 

Serial Port Configuration

 

 

 

 

Management Mode

 

: CONSOLE MODE

 

 

Baudrate

 

: 19200

 

 

 

Databits

 

: 8

 

 

 

Stopbits

 

: 1

 

 

 

Parity

 

 

: NONE

 

 

Time-Out (in minutes)

 

: 10

 

 

 

Auto Refresh (in seconds)

: 5

 

 

 

<APPLY>

<OK>

<CANCEL>

 

Use <TAB> or arrow keys to move, <Space> to scroll options.

 

 

 

 

 

 

Figure 2-11. Serial Port Configuration

 

 

 

 

 

 

Parameter

Default

Description

 

 

 

Management Mode

Console Mode

Indicates that the console port settings are for

 

 

 

direct console connection.

Baud Rate

Auto

The rate at which data is sent between devices.

 

 

 

Options : 2400, 4800, 9600, 19200 bps, and Auto

 

 

 

detection

 

 

 

Databits

8 bits

Sets the databits of the RS-232 port.

 

 

 

Options : 7, 8

 

 

Stopbits

1 bit

Sets the stop bits of the RS-232 port.

 

 

 

Options : 1, 2

 

 

Parity

none

Sets the parity of the RS-232 port.

 

 

 

Options : none/odd/even

Time-Out

10 minutes

If no input is received from the attached device

 

 

 

after this interval, the current session is

 

 

 

automatically closed.

 

 

 

Range : 0 - 100 minutes; 0: disabled

Auto Refresh

5 seconds

Sets the interval before a console session will

 

 

 

auto refresh the console information, such as

 

 

 

Spanning Tree Information, Port Configuration,

 

 

 

Port Statistics, and RMON Statistics.

Range : 5-255 seconds; 0: disabled

9033645-01

VH-2402S User Interface 19

Image 27
Contents Management Guide Fast Ethernet SwitchPage 9033645-01 9033645-01 Table of Contents Appendix A. Spanning Tree Concepts Snmp ManagementIndex Vi Table of Contents VH-2402S Console Port Out-of-Band Connections Configuration OptionsManagement Overview Required ConnectionsIn-Band Connections Configure the Switch SiteConfigure the Remote Site Remote Management via the Console PortIn-Band Network Connection Management Overview VH-2402S Overview VH-2402S User InterfaceUser Access Factory Default Settings Factory DefaultsGvrp Selection Description Main MenuDisplays/configures extended bridge capabilities provided by System Information Menu System Information MenuSystem Information Displaying System InformationSwitch Information Displaying Switch Version and Module InformationManagement Setup Menu Management Setup MenuNetwork Configuration Changing the Network ConfigurationIP Configuration IP ConfigurationIP Connectivity Test IP Connectivity Test Ping10. Http Configuration Http Configuration11. Serial Port Configuration Configuring the Serial PortAssigning Snmp Parameters 12. Snmp Configuration13. Snmp Communities Configuring Community Names14. IP Trap Managers Configuring IP Trap Managers15. Console Login Configuration Console Login ConfigurationDownloading System Software Using Tftp Protocol to Download Over the NetworkParameter Description Saving the System Configuration18. Management Configuration Configuring Management Access19. Device Control Menu Configuring the SwitchNot implemented in the current firmware release 20. Port Configuration Configuring Port Parameters21. Port Information Viewing the Current Port Configuration22. Spanning Tree Configuration Configuring Bridge STA Using the Spanning Tree AlgorithmDevice with the lowest MAC address will then 24. Spanning Tree Port Configuration Configuring STA for Ports or Modules25. Spanning Tree Information Viewing the Current Spanning Tree Configuration26. Bridge STA Information Displaying the Current Bridge STA27. Spanning Tree Port Information Displaying the Current STA for Ports or ModulesRules defining port status are 28. Mirror Port Configuration Using a Mirror Port for AnalysisConfiguring Port Trunks 29. Port Trunking Configuration Igmp Multicast Filtering 30. Igmp Configuration Configuring Igmp31. Broadcast Storm Control Configuration Configuring Broadcast Storm Control32. Extended Bridge Configuration Configuring Bridge MIB ExtensionsBy setting this parameter to False 33 .1P Configuration Configuring Traffic Classes34 .1P Port Priority Configuration Port Priority Configuration35 .1P Port Traffic Class Information 802.1P Port Traffic Class Information802.1Q Vlan Base Information Configuring Virtual LANs37 .1Q Vlan Current Table Information 802.1Q Vlan Current Table Information38 .1Q Vlan Static Table Configuration 802.1Q Vlan Static Table Configuration39 .1Q Vlan Static Table Configuration Example 40. Port Assignment Vlan Configuration Port Assignment Vlan Configuration41. Multicast Router Port Information Multicast Router Port Information42. Static Multicast Router Port Configuration Static Multicast Router Port Configuration43. Igmp Member Port Configuration Igmp Member Port Configuration44. Port Security Configuration Port Security Configuration45. Network Monitor Menu Monitoring the Switch46. Port Statistics Displaying Port Statistics47. Rmon Statistics Displaying Rmon StatisticsDrop Events 48. Unicast Address Table Displaying the Unicast Address Table49. IP Multicast Registration Table Displaying the IP Multicast Registration Table50. Static Unicast Addreeess Table Configuration Configuring Static Unicast AddressesLogging Off the System Resetting the System66 VH-2402S User Interface Common Tasks Configuring & Monitoring the SwitchSetting Password Protection Checking Network Configuration Status Connecting via TelnetAssigning an IP Address Viewing Switch Statistics Setting Snmp Management AccessDownloading a Software Upgrade Configuring Port MirroringDownloading Via Tftp Downloading Via the Serial Port9033645-01 Configuring Spanning Tree Parameters Configuring Class of Service Configuring VLANsConfiguring Port Operation Configuring the Unicast Address Table Configuring BootP Setting a Default GatewayConfiguring Port Trunks Configuring & Monitoring the Switch VH-2402S Snmp Protocol Snmp ManagementMIB Objects RFC 1493 Bridge MIB RFC 1213 MIB-IIRFC 1573 Interfaces Evolution MIB RFC 1643 Ethernet-Like MIBCompiling MIB Extensions Enterasys Website Ieee 802.1Q Q-MIBEnterasys Proprietary MIB Extensions Spanning Tree Features Appendix A. Spanning Tree ConceptsGeneral Spanning Tree Protocol in a Network Figure A-1. Spanning Tree Using VH-2402S SwitchesSpanning Tree Protocol Parameters Table A-1. Spanning Tree Protocol DefaultsSpanning Tree Protocol Operation 9033645-01 Spanning Tree Concepts VH-2402S VLANs and Frame Tagging Appendix B. Virtual Lans VlansPort Overlapping VH-2402S Vlan ConfigurationAssigning Ports to VLANs Vlan ClassificationAutomatic Vlan Registration Forwarding Tagged/Untagged FramesForwarding Traffic with Unknown Vlan Tags Incoming tagged frames contain a priority level range Appendix C. Class of ServiceFigure C-1. Class of Service Example Igmp Snooping and IP Multicast Filtering Appendix D. IP Multicast FilteringPage Index Tftp Page 150524-103 R02