Cypress CY7C68013 ECC Generation7, Gpif, USB Uploads and Downloads, Autopointer Access, Eccm =

Page 12

CY7C68013A, CY7C68014A CY7C68015A, CY7C68016A

3.13.3 GPIF and FIFO Clock Rates

An 8051 register bit selects one of two frequencies for the inter- nally supplied interface clock: 30 MHz and 48 MHz. Alternatively, an externally supplied clock of 5 MHz–48 MHz feeding the IFCLK pin can be used as the interface clock. IFCLK can be configured to function as an output clock when the GPIF and FIFOs are internally clocked. An output enable bit in the IFCONFIG register turns this clock output off, if desired. Another bit within the IFCONFIG register inverts the IFCLK signal whether internally or externally sourced.

3.15 ECC Generation[7]

The EZ-USB can calculate ECCs (Error Correcting Codes) on data that passes across its GPIF or Slave FIFO interfaces. There are two ECC configurations: Two ECCs, each calculated over 256 bytes (SmartMedia Standard); and one ECC calculated over 512 bytes.

The ECC can correct any one-bit error or detect any two-bit error.

3.15.1 ECC Implementation

The two ECC configurations are selected by the ECCM bit:

3.14 GPIF

The GPIF is a flexible 8-bit or 16-bit parallel interface driven by a user programmable finite state machine. It enables the CY7C68013A/15A to perform local bus mastering and can implement a wide variety of protocols such as ATA interface, printer parallel port, and Utopia.

The GPIF has six programmable control outputs (CTL), nine address outputs (GPIFADRx), and six general-purpose ready inputs (RDY). The data bus width can be 8 or 16 bits. Each GPIF vector defines the state of the control outputs, and determines what state a ready input (or multiple inputs) must be before proceeding. The GPIF vector can be programmed to advance a FIFO to the next data value, advance an address, etc. A sequence of the GPIF vectors make up a single waveform that is executed to perform the desired data move between the FX2LP and the external device.

3.14.1 Six Control OUT Signals

The 100-pin and 128-pin packages bring out all six Control Output pins (CTL0-CTL5). The 8051 programs the GPIF unit to define the CTL waveforms. The 56-pin package brings out three of these signals, CTL0–CTL2. CTLx waveform edges can be programmed to make transitions as fast as once per clock (20.8 ns using a 48-MHz clock).

3.14.2 Six Ready IN Signals

The 100-pin and 128-pin packages bring out all six Ready inputs (RDY0–RDY5). The 8051 programs the GPIF unit to test the RDY pins for GPIF branching. The 56-pin package brings out two of these signals, RDY0–1.

ECCM = 0

Two 3 byte ECCs, each calculated over a 256 byte block of data. This configuration conforms to the SmartMedia Standard.

Write any value to ECCRESET, then pass data across the GPIF or Slave FIFO interface. The ECC for the first 256 bytes of data is calculated and stored in ECC1. The ECC for the next 256 bytes is stored in ECC2. After the second ECC is calculated, the values in the ECCx registers do not change until ECCRESET is written again, even if more data is subsequently passed across the interface.

ECCM = 1

One 3 byte ECC calculated over a 512 byte block of data.

Write any value to ECCRESET then pass data across the GPIF or Slave FIFO interface. The ECC for the first 512 bytes of data is calculated and stored in ECC1; ECC2 is unused. After the ECC is calculated, the values in ECC1 do not change even if more data is subsequently passed across the interface, till ECCRESET is written again.

3.16 USB Uploads and Downloads

The core has the ability to directly edit the data contents of the internal 16 KByte RAM and of the internal 512 byte scratch pad RAM via a vendor specific command. This capability is normally used when soft downloading user code and is available only to and from internal RAM, only when the 8051 is held in reset. The available RAM spaces are 16 KBytes from 0x0000–0x3FFF (code/data) and 512 bytes from 0xE000–0xE1FF (scratch pad data RAM).[8]

3.14.3 Nine GPIF Address OUT Signals

Nine GPIF address lines are available in the 100-pin and 128-pin packages, GPIFADR[8..0]. The GPIF address lines enable indexing through up to a 512 byte block of RAM. If more address lines are needed IO port pins are used.

3.14.4 Long Transfer Mode

In the master mode, the 8051 appropriately sets GPIF trans- action count registers (GPIFTCB3, GPIFTCB2, GPIFTCB1, or GPIFTCB0) for unattended transfers of up to 232 transactions. The GPIF automatically throttles data flow to prevent under or overflow until the full number of requested transactions complete. The GPIF decrements the value in these registers to represent the current status of the transaction.

3.17 Autopointer Access

FX2LP provides two identical autopointers. They are similar to the internal 8051 data pointers but with an additional feature: they can optionally increment after every memory access. This capability is available to and from both internal and external RAM. The autopointers are available in external FX2LP registers under control of a mode bit (AUTOPTRSET-UP.0). Using the external FX2LP autopointer access (at 0xE67B – 0xE67C) enables the autopointer to access all internal and external RAM to the part.

Also, the autopointers can point to any FX2LP register or endpoint buffer space. When autopointer access to external memory is enabled, location 0xE67B and 0xE67C in XDATA and code space cannot be used.

Notes

7.To use the ECC logic, the GPIF or Slave FIFO interface must be configured for byte-wide operation.

8.After the data has been downloaded from the host, a “loader” can execute from internal RAM to transfer downloaded data to external memory.

Document #: 38-08032 Rev. *L

Page 12 of 62

[+] Feedback

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Features CY7C68013A/14A/15A/16A Cypress Semiconductor Corporation 198 Champion CourtLogic Block Diagram Features CY7C68013A/14A onlyFeatures CY7C68015A/16A only Applications Functional OverviewUSB Boot Methods Bus-powered ApplicationsReNumeration Interrupt SystemINT2 USB Interrupts Priority INT2VEC Value SourceFIFO/GPIF Interrupt INT4 Reset and Wakeup Reset PinReset Timing Values Condition Program/Data RAMInside FX2LP Outside FX2LP Internal Code Memory, EA =Register Addresses External Code Memory, EA =Setup Data Buffer Endpoint Configurations High -speed ModeEndpoint RAM Size × 64 bytes Endpoints 0 × 512 bytes12.5 Default Full-Speed Alternate Settings Master/Slave Control SignalsExternal Fifo Interface ArchitectureAutopointer Access ECC Generation7Gpif USB Uploads and Downloads18 I2C Controller Compatible with Previous Generation EZ-USB FX2Part Number Conversion Table Package DescriptionPin Assignments 20 CY7C68013A/14A and CY7C68015A/16A DifferencesIfclk PE0 PE1128 CY7C68013A/CY7C68014A Pin TqfpCY7C68013A/CY7C68014A CY7C68013A/CY7C68014A 56-pin Ssop CY7C68013A/CY7C68014A 56-pin Ssop Pin AssignmentCY7C68015A/CY7C68016A Pin QFN CY7C68013A 56-pin Vfbga Pin Assignment Top View FX2LP Pin Descriptions 128 100 56 VF Name Type Default CY7C68013A/15A Pin Descriptions56 VF Name Type Default Description FX2LP Pin DescriptionsPort IFCONFIG1..0 WU2FIFOADR0 FIFOADR1GPIFADR0 PORTCCFG.0GPIFADR1 PORTCCFG.1Port E T0OUTT1OUT T2OUTRXD1OUT INT6T2EX GPIFADR8Flagb FlagcCTL3 CTL4Ground Register Summary FX2LP Register SummaryRegister can only be reset, it cannot be set Epie EP0CS E6CB Flowstb DPL0 = both read/write bit Thermal Characteristics Absolute Maximum RatingsOperating Conditions ΘJc + θCaDC Characteristics AC Electrical CharacteristicsUSB Transceiver Program Memory Read ClkoutProgram Memory Read Parameters Description Min Typ Max Unit Data Memory Read CLKOUT17Data Memory Read Parameters Description Min Typ Max Unit Data Memory Write Stretch =Data Memory Write Parameters Description Min Max Unit Portc Strobe Feature Timings WR# Strobe Function when Portc is Accessed byGpif Synchronous Signals Gpif Synchronous Signals Timing Diagram20Slave Fifo Synchronous Read Timing Diagram20 Slave Fifo Synchronous ReadSlave Fifo Asynchronous Read Timing Diagram20 Slave Fifo Asynchronous ReadSlave Fifo Synchronous Write Timing Diagram20 Slave Fifo Synchronous WriteSlave Fifo Asynchronous Write Slave Fifo Synchronous Packet End StrobeSlave Fifo Synchronous Write Sequence and Timing Diagram Slave Fifo Asynchronous Packet End StrobeSlave Fifo Output Enable Slave Fifo Address to Flags/DataFIFOADR10 to SLRD/SLWR/PKTEND Setup Time Slave Fifo Synchronous AddressSlave Fifo Asynchronous Address RD/WR/PKTEND to FIFOADR10 Hold TimeSequence Diagram Single and Burst Synchronous Read Example10.17.2 Single and Burst Synchronous Write Sequence Diagram of a Single and Burst Asynchronous Read Slave Fifo Asynchronous Read Sequence and Timing Diagram20Sequence Diagram of a Single and Burst Asynchronous Write Slave Fifo Asynchronous Write Sequence and Timing Diagram20Ideal for battery powered applications Ideal for non-battery powered applicationsOrdering Information Development Tool KitPackage Diagrams Lead Shrunk Small Outline Package O56Lead QFN 8 x 8 mm LF56A Pin Thin Plastic Quad Flatpack 14 x 20 x 1.4 mm A100RA Lead Thin Plastic Quad Flatpack 14 x 20 x 1.4 mm A128 PCB Layout Recommendations Vfbga 5 x 5 x 1.0 mm 0.50 Pitch, 0.30 Ball BZ56Quad Flat Package No Leads QFN Package Design Notes Cross-section of the Area Underneath the QFN PackageIssue Orig. Description of Change Date Cmcc Pyrs

CY7C68016A, CY7C68014A, CY7C68015A, CY7C68013 specifications

The Cypress CY7C68013, CY7C68015A, CY7C68014A, and CY7C68016A are part of Cypress Semiconductor's EZ-USB family of microcontrollers, known for their high performance and flexibility in USB applications. These devices are primarily used for USB interfacing and have gained popularity in various industries due to their robust features and capabilities.

One of the main features of the CY7C68013 is its Dual FIFO architecture, allowing for efficient data transfer between USB and the system memory. This feature optimizes throughput and reduces CPU overhead, making it an excellent choice for applications that require high-speed data exchange, such as video streaming, data acquisition, and industrial automation. The device is equipped with a USB 2.0 interface which supports full-speed operation at 12 Mbps, ensuring compatibility with a wide range of USB devices.

The CY7C68015A, a similar variant, offers additional memory options, providing users with the flexibility to select the necessary capacity for their specific applications. This part is particularly useful in scenarios that demand more users or higher data storage, making it ideal for complex USB peripherals like printers and multifunction devices. Moreover, it includes a unique capability of upgradeable firmware, ensuring that the device remains relevant and functional as technology evolves.

In contrast, the CY7C68014A stands out with its support for isochronous data transfers, making it suitable for real-time applications that require timely data delivery. This is particularly important in audio and video applications where delays can impact performance. The device incorporates advanced power management features, allowing it to operate efficiently both in low and high-power modes.

Lastly, the CY7C68016A integrates enhanced security features, positioning it as an ideal choice for applications that require data integrity and protection against unauthorized access. It supports various encryption standards and provides secure boot capabilities, making it suitable for secure environments such as financial transactions and sensitive data processing.

In summary, the CY7C68013, CY7C68015A, CY7C68014A, and CY7C68016A microcontrollers offer a versatile suite of features that cater to a wide array of USB applications. Their design emphasizes performance, flexibility, and security, making them essential components in today's rapidly evolving technology landscape. Whether in consumer electronics, industrial automation, or specialized applications, these devices provide the reliability and efficiency that engineers and developers require.
Top Page Image Contents