Cyclades PM IPDU Resetting the Admin Password, To save the configuration with the save command

Page 37

Chapter 3: Configuration	25

To save the configuration with the save command:

1.Login to the PM IPDU.

2.Enter the save command to save the configuration.

Resetting the Admin Password

In the event the administrator wants to reset the password for the Cyclades PM IPDU (for example, if the administrator forgets the admin password), then the loopback connector that is shipped with the Cyclades PM IPDU may be used for temporary access to the PM IPDU.

To reset the admin password using the loopback connector:

1.If you are not logged out, log out by entering exit. (You must be at the login prompt for this to work.)

2.Attach the loopback connector.

Connect the loopback connector shipped with the product to the OUT port of the Cyclades PM IPDU. If necessary, disconnect any cables connected to the OUT port of the Cyclades PM IPDU to allow for the connection of the loopback.

3.Wait one minute and then check the display.

If you are watching the Cyclades PM IPDU's console output (using HyperTerminal or Minicom), messages like the ones shown below are displayed:

AlterPath PM

Copyright (c) 2002-2006 Avocent Corporation

V 1.9.0 Jun 21, 2006

Username: [PM]: DCD went ON on output port of IPDU #1

[PM]: Trying to detect loopback cable on OUT port of IPDU #1

[PM]: Loopback detected. Changing administrator password to default.

[PM]: Please remove the loopback cable now.

[PM]: DCD went OFF on output port of IPDU #1

[PM]: IPDU: 1

[PM]: OUT: 8

4.Remove the loopback connector.

After one minute, you may remove the loopback connector from the OUT port of the Cyclades PM IPDU. Now the password for the user admin is reset to the default (pm8), and you should be able to log into the Cyclades PM IPDU using the default username/password.

5.Change the password for the admin, if desired, by entering the passwd command.

6.Enter the save command to save the configuration.

Image 37

Contents Cyclades P M Ipdu FCC Warning Statement Canadian DOC Notice Cyclades PM Ipdu Power On Table of Contents Configuration Appendices Vi Cyclades PM Ipdu Installer/Administrator/User Guide List of Figures Viii Cyclades PM Ipdu Installer/Administrator/User Guide List of Tables Cyclades PM Ipdu Installer/Administrator/User Guide Alarms and monitoring Features and BenefitsSequential power up Standalone configuration Hardware Configuration OptionsSupport for daisy chaining Creation of user accountsStandalone Configuration Daisy chained configurationUser Integrated configurationPM Ipdu #2 PM Ipdu #3 PM Ipdu #4 An integrated environment offers the following advantagesDirect console access Accessing the System ConsoleConsole access through a management device To connect a Cyclades PM Ipdu to an Avocent DSR switchCyclades PM8 Ipdu Component OverviewCyclades PM10 Ipdu Cyclades PM8i IpduCyclades PM10i-L30A Ipdu Cyclades PM10i IpduCyclades PM10i-32A Ipdu Cyclades PM20 Ipdu Cyclades PM10i-32Au IpduCyclades PM20i Ipdu Cyclades PM20i-32Au Ipdu Cyclades PM20i-32A IpduCyclades PM Ipdu Installer/Administrator/User Guide Supplied with the PM Ipdu Getting StartedConnector on Modular input power cables for the PM IpduPM8i-10A Ipdu and PM10i-10A Ipdu power cables PM10i-16A Ipdu and PM 20i-16A Ipdu power cables PM10i-15A Ipdu power cablesPM10i-20A Ipdu and PM 20i-20A Ipdu power cables Rack Mounting the Cyclades PM IpduRack Mounting a Cyclades PM10 IPDU, PM10l Ipdu and PM8iIPDU Installation environmentLocate the appropriate sets of holes on the PM Ipdu To mount the Cyclades PM8i IPDU, PM10 Ipdu or PM10i IpduTo daisy chain a PM Ipdu Daisy Chaining PM IPDUsMaking a Direct Connection for Console Access Powering Up the PM IpduTo power up the PM Ipdu Plugging Devices Into PM Ipdu OutletsConnecting a Local Work Station to the Cyclades PM Ipdu To access the consoleTo log into the PM Ipdu through the console in port Default Configuration Parameters ConfigurationTo change the default password Initial Configuration Using the Command PromptTo create users with the adduser command To assign outlets to users with the assign commandTo save the configuration with the save command Resetting the Admin PasswordTo reset the admin password using the loopback connector Upgrading the Cyclades PM Ipdu Firmware To upgrade PM Ipdu firmwareTo use HyperTerminal in Windows PmupgradeTo use Minicom in Linux Sending Firmware using HyperTerminalSending Firmware using Minicom Cyclades PM Ipdu Installer/Administrator/User Guide PM Ipdu User Interface Daisy chained PM IPDUs in the login promptNumber of PM IPDUs Number of PM Ipdu outletsLogging in to the PM Ipdu CommandsSyntax AdduserArguments ExamplesAssign AlarmTo set the threshold, enter the following To read the threshold, enter the followingCurrent BuzzerTo turn buzzer notification on or off, enter the following Pmcurrent reset To reset maximum current drawn, enter the followingCurrentprotection Pm currentExample CurrsegTo view the current load of segment A, enter the following To view the current load of segment B, enter the following CycleTo cycle one outlet, enter the following Deluser DbsyncTo cycle multiple outlets, enter the following NoneTo delete the user rog, enter the following DisplayPmdeluser rog Pmdisplay 2Exit command exits the session FactorydefaultsExit To view the display status, enter the followingPmfactorydefaults To reset the factory defaults, enter the followingHelp Pmsyslog helpPmhelp HumidityHwocp Pmhumidity resetPm humidity To set the ID of PM Ipdu 1 R&D, enter the following Pmhwocp 1 resetPmhwocp Pmid 1 R&DTo display the ID of PM Ipdu 2, enter the following IntervalTo display the interval of outlet 1, enter the following PmidPminterval 2,4-6 ListPmlist Name LockTo lock outlets 1, 2, and 6, enter the following To name outlet 4 as nowhere, enter the followingTo turn all outlets off, enter the following OffPmoff all PmoffTo turn on outlets 1, 3, 4, and 5, type PasswdPmon 1 Pmpasswd alpha RebootPmpasswd Pmreboot Pmrestore RestoreSave Arguments ExamplesStatus command displays the status of selected outlets To save the configuration to flash, enter the followingStatus To display the status of outlet 1, enter the followingTo display the status of all outlets, enter the following SyslogPmstatus all PmsyslogPm temperature TemperaturePmtemperature reset Pmsyslog onUnlock UnassignTo unlock outlets 2, 3, 4, and 8, enter the following Pmunassign 2,4 diderotUpgrade Ver To upgrade 1, typePmver VoltageTo view the current username, enter the following WhoamiPmwhoami Cyclades PM Ipdu Installer/Administrator/User Guide Appendix a Specifications Cyclades PM Ipdu Installer/Administrator/User Guide Appendices Cyclades PM Ipdu Installer/Administrator/User Guide Appendices Table A.11 PM10i-32A Ipdu and PM10i-32Au Ipdu Specifications Table A.13 PM20-20A Ipdu and PM20-L20A Ipdu Specifications Cyclades PM Ipdu Installer/Administrator/User Guide Appendices Interface Pinouts Safety Instructions Appendix B Safety InstructionsSicherheitsanweisungen Istruzioni di Sicurezza Instruções de Segurança Instrucciones de seguridad Instructions de sécurités PM Ipdu Units with One Circuit Breaker Appendix C Circuit BreakersPM8i Ipdu and PM10i Ipdu PM10i-32A Ipdu and PM10i-32Au Ipdu PM10i-L30A IpduPM20i-L30A Ipdu PM20-L30A IpduPM20i-32A Ipdu and PM20i-32Au Ipdu Circuit Breaker Trip Time Cyclades PM Ipdu Installer/Administrator/User Guide Index Cyclades PM Installer/Administrator/User Guide Index Cyclades PM Installer/Administrator/User Guide Page 590-667-501A