Buffalo Technology WBR2-G54S user manual Click on the ‘LAN port’ link on the left

Page 81

Troubleshooting

5.Click on the ‘LAN port’ link on the left.

6.Check that the ‘LAN side IP address’ values are correct for your network, or leave them as default. Record the ‘LAN side IP address’. Press the ‘Set’ button if any settings on this page have been set.

7.Click on the ‘Management’ link on the left.

8.The System Information page will appear. In the Wireless section of the table record the MAC ad- dress (including the :’s). Please make sure the MAC address is recorded from the Wireless section and not the other sections.

9.Logout of the access point by clicking on the ‘Logout’ link on the left. Close the browser window.

10.Login to the second access point in the wireless bridge.

11.Click on the ‘Advanced’ button.

12.The wireless settings page will appear. Select the proper settings for the wireless network. Refer to the settings recorded from the fi rst access point. All settings except for the SSID need to be identical amongst all access points in the bridge.

(If roaming is desired, then make sure the SSID settings need to be identical as well).

13.Click on the ‘LAN port’ link on the left.

14.Make sure that the ‘LAN side IP address’ ‘IP address’ setting is different then the fi rst access point. The IP addresses cannot be the same, but they should be on the same network. It is recommended that the IP address of the second access point is one higher then that of the fi rst access point. Thus, if access point one’s address is 1.1.1.1, then access point two’s address should be 1.1.1.2. If there is a ‘DHCP server function’ setting on this page, then make sure to set it to ‘Do not use’ or to ‘Disabled’. Press the ‘Set’ button when fi nished.

81

Image 81
Contents WBR2-G54S Table of Contents Network Settings Table of Contents Introduction Introduction SOHO/SMB Networking Home NetworkingSystem Requirements AirStation WBR2-G54S Package ContentsProduct Views About the AirStation CD Installation / Setup Setup Preparation Setup OverviewIntroduction Antenna Installation Open the Setup Screen Standard SettingsEnter ISP information DSL ButtonAutomatic IP Assignment by ISP PPPoE Connection Enter IP Address ManuallyCatv Cable Button Line Test Security Simple Security Setup Applications Refer to the on-screen help for Aoss Aoss Additional Aoss Information LAN Settings Advanced SettingsWireless Settings Wireless Function Enable orAdvanced Settings Wireless LAN Security Advanced Settings Characteristics Advanced Settings LAN Port Dhcp Server Advanced Settings Manual IP MAC Address Assignment Settings Wireless PC’s Connection Wireless MAC FilterRegister for Allowable PC’s MAC Address Wireless Bridge WDS Advanced Settings WAN Settings Wired WAN PerformanceWAN Port Connection Type Select from MRU Maximum Receive MTU Maximum TransmitWAN Network Advanced Settings Routing Setup Network SettingsAdd Routing Table Entry Enable or Disable . Address Address TranslationIP Masquerade When Display/Delete NAT Table Add NAT Table Advanced Settings Log Output Select Output to Packet FilterBasic Filter Setting IP Filter Setting MAC Filter Click Enter MAC Lter to enter MAC address Click Apply when settings are complete DETECTOR@AIRSTATION Intrusion DetectorPage UPnP System Information ManagementAdmin Name Password Time setup Select Use or Do not useNTP server name Enter Packet Traffic Information Wired WAN Wired LAN Wireless LANIP Address and Medium Client MonitorPing Test Log Information Display log info SelectLog information Displays Syslog Transfer Log Information LevelLog Information Select Save/Restore Settings Save current settings ClickRestored saved settings Reboot/Reload Defaults Click Restart to rebootAirStation Firmware Update Com/wirelessFirmware file name Client Table Displays AossManually specify the encryp Aoss Function Click EnablePower Characteristics Temperature & HumiditySpecifications Additional InformationRadio Characteristics Networking CharacteristicsRegulatory Information Host Operating SystemOpen Office Environment Semi-Open Office Environment 2412 Common Problems TroubleshootingLED Activity B Diag LED ActivityChanging Client TCP/IP Settings in Windows Table B.1.1 Diag LED Activity TableLEDs Work But Client PC Cannot Connect to Network Other Problems Problem CauseRestrictions Proper Setup Click on the ‘LAN port’ link on the left Troubleshooting Troubleshooting Glossary Glossary MHz MegaHertz One million cycles per second ROM Read Only Memory Permanent memory PCI Peripheral Component Interconnect aGlossary Glossary Federal Communication Commission Interference Statement FCC / CE InformationFederal Communication Commission Interference Statement Important NoteEU Countries intended for use FCC RF Radiation Exposure StatementEU Countries Not intended for use Potential restrictive useWarranty Information General Inquiries Contact Information4030 W. Braker Ln. Suite Austin, Texas Tel Fax