Buffalo Technology WBR2-G54S user manual Important Note

Page 91

FCC / CE Information

IMPORTANT NOTE:

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

91

Image 91

Contents WBR2-G54S Table of Contents Network Settings Table of Contents Introduction Introduction SOHO/SMB Networking Home NetworkingSystem Requirements AirStation WBR2-G54S Package ContentsProduct Views About the AirStation CD Installation / Setup Setup Overview Setup PreparationIntroduction Antenna Installation Open the Setup Screen Standard SettingsDSL Button Enter ISP informationAutomatic IP Assignment by ISP PPPoE Connection Enter IP Address ManuallyCatv Cable Button Line Test Security Simple Security Setup Applications Refer to the on-screen help for Aoss Aoss Additional Aoss Information Wireless Function Enable or Advanced SettingsLAN Settings Wireless SettingsAdvanced Settings Wireless LAN Security Advanced Settings Characteristics Advanced Settings LAN Port Dhcp Server Advanced Settings Manual IP MAC Address Assignment Settings Wireless PC’s Connection Wireless MAC FilterRegister for Allowable PC’s MAC Address Wireless Bridge WDS Advanced Settings Wired WAN Performance WAN SettingsWAN Port Connection Type Select from MRU Maximum Receive MTU Maximum TransmitWAN Network Advanced Settings Routing Setup Network SettingsAdd Routing Table Entry Address Translation Enable or Disable . AddressIP Masquerade When Display/Delete NAT Table Add NAT Table Advanced Settings Log Output Select Output to Packet FilterBasic Filter Setting IP Filter Setting MAC Filter Click Enter MAC Lter to enter MAC address Click Apply when settings are complete DETECTOR@AIRSTATION Intrusion DetectorPage UPnP System Information ManagementAdmin Name Password Select Use or Do not use Time setupNTP server name Enter Packet Trafﬁc Information Wired WAN Wired LAN Wireless LANIP Address and Medium Client MonitorPing Test Display log info Select Log InformationLog information Displays Log Information Level Syslog TransferLog Information Select Save current settings Click Save/Restore SettingsRestored saved settings Click Restart to reboot Reboot/Reload DefaultsAirStation Com/wireless Firmware UpdateFirmware ﬁle name Client Table Displays AossManually specify the encryp Aoss Function Click EnableAdditional Information Temperature & HumidityPower Characteristics SpeciﬁcationsHost Operating System Networking CharacteristicsRadio Characteristics Regulatory InformationOpen Ofﬁce Environment Semi-Open Ofﬁce Environment 2412 Diag LED Activity TroubleshootingCommon Problems LED Activity BTable B.1.1 Diag LED Activity Table Changing Client TCP/IP Settings in WindowsLEDs Work But Client PC Cannot Connect to Network Other Problems Cause ProblemRestrictions Proper Setup Click on the ‘LAN port’ link on the left Troubleshooting Troubleshooting Glossary Glossary MHz MegaHertz One million cycles per second ROM Read Only Memory Permanent memory PCI Peripheral Component Interconnect aGlossary Glossary Federal Communication Commission Interference Statement FCC / CE InformationFederal Communication Commission Interference Statement Important NotePotential restrictive use FCC RF Radiation Exposure StatementEU Countries intended for use EU Countries Not intended for useWarranty Information General Inquiries Contact Information4030 W. Braker Ln. Suite Austin, Texas Tel Fax