Buffalo Technology WBR2-G54S user manual FCC / CE Information

Page 90

FCC / CE Information

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is con- nected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

90

Image 90
Contents WBR2-G54S Table of Contents Network Settings Table of Contents Introduction Introduction Home Networking SOHO/SMB NetworkingAirStation WBR2-G54S Package Contents System RequirementsProduct Views About the AirStation CD Installation / Setup Setup Preparation Setup OverviewIntroduction Antenna Installation Standard Settings Open the Setup ScreenEnter ISP information DSL ButtonAutomatic IP Assignment by ISP Enter IP Address Manually PPPoE ConnectionCatv Cable Button Line Test Security Simple Security Setup Applications Refer to the on-screen help for Aoss Aoss Additional Aoss Information Wireless Settings Advanced SettingsLAN Settings Wireless Function Enable orAdvanced Settings Wireless LAN Security Advanced Settings Characteristics Advanced Settings LAN Port Dhcp Server Advanced Settings Manual IP MAC Address Assignment Settings Wireless MAC Filter Wireless PC’s ConnectionRegister for Allowable PC’s MAC Address Wireless Bridge WDS Advanced Settings WAN Settings Wired WAN PerformanceWAN Port Connection Type Select from MTU Maximum Transmit MRU Maximum ReceiveWAN Network Advanced Settings Network Settings Routing SetupAdd Routing Table Entry Enable or Disable . Address Address TranslationIP Masquerade When Display/Delete NAT Table Add NAT Table Advanced Settings Packet Filter Log Output Select Output toBasic Filter Setting IP Filter Setting MAC Filter Click Enter MAC Lter to enter MAC address Click Apply when settings are complete Intrusion Detector DETECTOR@AIRSTATIONPage UPnP Management System InformationAdmin Name Password Time setup Select Use or Do not useNTP server name Enter Wired WAN Wired LAN Wireless LAN Packet Traffic InformationClient Monitor IP Address and MediumPing Test Log Information Display log info SelectLog information Displays Syslog Transfer Log Information LevelLog Information Select Save/Restore Settings Save current settings ClickRestored saved settings Reboot/Reload Defaults Click Restart to rebootAirStation Firmware Update Com/wirelessFirmware file name Aoss Client Table DisplaysAoss Function Click Enable Manually specify the encrypSpecifications Temperature & HumidityPower Characteristics Additional InformationRegulatory Information Networking CharacteristicsRadio Characteristics Host Operating SystemOpen Office Environment Semi-Open Office Environment 2412 LED Activity B TroubleshootingCommon Problems Diag LED ActivityChanging Client TCP/IP Settings in Windows Table B.1.1 Diag LED Activity TableLEDs Work But Client PC Cannot Connect to Network Other Problems Problem CauseRestrictions Proper Setup Click on the ‘LAN port’ link on the left Troubleshooting Troubleshooting Glossary Glossary MHz MegaHertz One million cycles per second PCI Peripheral Component Interconnect a ROM Read Only Memory Permanent memoryGlossary Glossary FCC / CE Information Federal Communication Commission Interference StatementImportant Note Federal Communication Commission Interference StatementEU Countries Not intended for use FCC RF Radiation Exposure StatementEU Countries intended for use Potential restrictive useWarranty Information Contact Information General Inquiries4030 W. Braker Ln. Suite Austin, Texas Tel Fax