Buffalo Technology WBR2-G54S user manual Advanced Settings

Page 27

Advanced Settings

If there are multiple APs in close proximity using the same channel, there may be interference. In this case, change to a non-overlapping channel.

Privacy Separator - Enable or disable communication between wireless clients. If you choose to use this feature, every wireless client that is associated to the AirStation will not be able to communicate with any other wireless clients.

■Note: If this function is used, wired clients can still communicate with wireless clients.

BSS (Basic Service Set) Basic Rate Set - The transmission data rates offered by the AirStation. It is recommended to use the ‘Default’ selection to accomidate 802.11 and 802.11b rate sets. It is NOT recom- mended to use the ‘All’ selection, as some devices may not understand all of the rate sets offered by the AirStation.

Frame Bursting - This function increases 802.11g communication throughput by transferring packets more efﬁciently. The following conditions affect this function:

•The wireless LAN client adapter must support Frame Bursting (and it must be enabled). If the wireless LAN client adapter does not support Frame Bursting, or Frame Bursting is not enabled, then it will operate at non-Frame Bursting speeds.

125 High Speed Mode - This function further increases 802.11g communication. Rate sets up to 125 Mbps are offered to clients.The following conditions affect this function:

•The wireless LAN client adapter must support 125 High Speed Mode (and it must be enabled). If the wireless LAN client adapter does not support 125 High Speed Mode, or it is not enabled, then it will operate at regular 802.11g speeds.

It is recommended to leave 125 High Speed Mode enabled as it can only help throughput, not hurt it.

27

Image 27

Contents WBR2-G54S Table of Contents Network Settings Table of Contents Introduction Introduction SOHO/SMB Networking Home NetworkingSystem Requirements AirStation WBR2-G54S Package ContentsProduct Views About the AirStation CD Installation / Setup Setup Preparation Setup OverviewIntroduction Antenna Installation Open the Setup Screen Standard SettingsEnter ISP information DSL ButtonAutomatic IP Assignment by ISP PPPoE Connection Enter IP Address ManuallyCatv Cable Button Line Test Security Simple Security Setup Applications Refer to the on-screen help for Aoss Aoss Additional Aoss Information Wireless Function Enable or Advanced SettingsLAN Settings Wireless SettingsAdvanced Settings Wireless LAN Security Advanced Settings Characteristics Advanced Settings LAN Port Dhcp Server Advanced Settings Manual IP MAC Address Assignment Settings Wireless PC’s Connection Wireless MAC FilterRegister for Allowable PC’s MAC Address Wireless Bridge WDS Advanced Settings WAN Settings Wired WAN PerformanceWAN Port Connection Type Select from MRU Maximum Receive MTU Maximum TransmitWAN Network Advanced Settings Routing Setup Network SettingsAdd Routing Table Entry Enable or Disable . Address Address TranslationIP Masquerade When Display/Delete NAT Table Add NAT Table Advanced Settings Log Output Select Output to Packet FilterBasic Filter Setting IP Filter Setting MAC Filter Click Enter MAC Lter to enter MAC address Click Apply when settings are complete DETECTOR@AIRSTATION Intrusion DetectorPage UPnP System Information ManagementAdmin Name Password Time setup Select Use or Do not useNTP server name Enter Packet Trafﬁc Information Wired WAN Wired LAN Wireless LANIP Address and Medium Client MonitorPing Test Log Information Display log info SelectLog information Displays Syslog Transfer Log Information LevelLog Information Select Save/Restore Settings Save current settings ClickRestored saved settings Reboot/Reload Defaults Click Restart to rebootAirStation Firmware Update Com/wirelessFirmware ﬁle name Client Table Displays AossManually specify the encryp Aoss Function Click EnableAdditional Information Temperature & HumidityPower Characteristics SpeciﬁcationsHost Operating System Networking CharacteristicsRadio Characteristics Regulatory InformationOpen Ofﬁce Environment Semi-Open Ofﬁce Environment 2412 Diag LED Activity TroubleshootingCommon Problems LED Activity BChanging Client TCP/IP Settings in Windows Table B.1.1 Diag LED Activity TableLEDs Work But Client PC Cannot Connect to Network Other Problems Problem CauseRestrictions Proper Setup Click on the ‘LAN port’ link on the left Troubleshooting Troubleshooting Glossary Glossary MHz MegaHertz One million cycles per second ROM Read Only Memory Permanent memory PCI Peripheral Component Interconnect aGlossary Glossary Federal Communication Commission Interference Statement FCC / CE InformationFederal Communication Commission Interference Statement Important NotePotential restrictive use FCC RF Radiation Exposure StatementEU Countries intended for use EU Countries Not intended for useWarranty Information General Inquiries Contact Information4030 W. Braker Ln. Suite Austin, Texas Tel Fax