AVE VSI-PRO Download Setup Upload Setup Update Firmware Exit, Download Setup Upload Setup Exit

Page 48

PROGRAMMING

To proceed with the DOWNLOAD/UPLOAD SETUP, we will configure the UNPROGRAMMED VSI-Pro first. From the main-menu, press the “Up” or “Down” button to move the cursor to “DOWNLOAD/UPLOAD SETUP” and press “Set”. The following sub-menu will appear:

DOWNLOAD SETUP

UPLOAD SETUP

UPDATE FIRMWARE

EXIT

Figure 80: DOWNLOAD/UPLOAD SETUP Sub-Menu

Press the “Up” or “Down” button to move the cursor to “DOWNLOAD SETUP” and press “Set”. The following sub- menu will appear. Move to the cursor to “DOWNLOAD SETUP” and press “Set” and the display “DOWNLOAD SETUP...” will appear:

DOWNLOAD SETUP

UPLOAD SETUP

EXIT

DOWNLOAD SETUP ...

Figure 81: DOWNLOAD SETUP Sub-Menu & Display

The UNPROGRAMMED VSI-Pro is now waiting to receive data from the PROGRAMMED VSI-Pro.

Now go to the main-menu of the PROGRAMMED VSI-Pro and follow the previous instructions to get to “UPLOAD SETUP” and press “Set”. The following sub-menu will appear. Move to the cursor to “UPLOAD SETUP” and press “Set” and the display “UPLOAD SETUP...” will appear:

DOWNLOAD SETUP UPLOAD SETUP EXIT

01

UPLOAD SETUP ...

Figure 82: UPLOAD SETUP Sub-Menu & Display

The data transfer will begin and you will have a screen count down of the status that reads:

Programmed VSI

Unprogrammed VSI

UPLOADING ...DOWNLOADING ...

The count will end at 100. When this prompt clears the screen, the data transfer is complete. Press “Reset” to exit this menu on both VSI-Pro’s.

Now go to the main-menu of the previously UNPROGRAMMED VSI-Pro on the right side of the screen. Enter the EXCEPTIONS menu. You should see your exceptions and other programmed data just as they were on the original PROGRAMMED VSI-Pro.

VSI-Pro VIDEO SERIAL INTERFACE

48

Image 48

Contents VSI-PRO JuneVSI-Pro Contents Contents Gasboy Sub-Menu Download/Upload Sub-Menu Introduction VSI / VSI+ / VSI-Pro Backward CompatibilityFeatures & Specifications FeaturesFeatures & Specifications SpecificationsConnections VSI-Pro Rear PanelPIN # Signal Name RS232 PIN # Function DirectionDTR DSRVSI-PRO VSI-Pro ConnectionsUser Front Panel Controls Front Panel ControlsChanging the Horizontal Position Programming Getting StartedMain Programming Menu Register SelectNext page Exit TCP/IP LimitationsSET Address ANY Exit SET AddressDisplay Receipt Exit DisplayModel Display Journal ExitDevice CON Sole Device Address Exit DeviceOperator Customer Combined Exit Journal Receipt Check Credit ExitLocal VSS Micros IDN Network Micros ISN Network Exit Device Printer Device Address ANY Modetap ExitTitle Display on Console ID ANY Working Mode Exit Model Working Mode ExitWoking Mode NCR Jrnl Printer NCR Rcpt Printer NCR Slip PrinterModel TK-T500 Mode Emulating Exit Device Address ExitDevice Address ANY Address Exit Next page ExitSET Term no Choices ALL, 1, 2, 3,..., 253, 254Journal Printer Receipt Printer Choices RECEIPT, CDU 2L , C.D.UScreen Setup Text GrayscaleBackground Grayscale Clock Sub-Menu Text Display Titler OFF ExitTitle Screen Blank Display Lines Display FormatScreen Blank Choices NONE, 6, 12, 20, 30, 60, 120, 180Line Compress Left JustificationCommunication Interface TypeRS-232 Choices RS-232, Passive TAP, RS-485Exception Reports Choices NONE, ODD, EvenChoices 7 or Exception Report OverviewHard Alarm Output ON-SCREEN FlagsPrinter or DVR Output Exception History SET Exception Output Time Stamp Exit Exception HistoryTotal Exception Total ExceptionsTime Search Time Search Setting DMS-3001 DVR-3011.3021Dest ID SCR ID Exit Choices 1 throughExample 0000.00 Operator None ExitException no History Buffer ON/OFF Scroll Matching Exception Strings ON/OFFProgramming Note Negative ExceptionPage OUT Range Greater thanLess than Alarm Outputs Alarm noException Report Menu Output Triggered Text ExitRTS Normal StateChoices no Normally open, NC Normal closed Choices 6, 12, 30, 60, 120, 180 Triggered TextDisplay Text OFF Output Text SET Triggered Exit Display TextTEST/DEMO Mode SET Triggered TextDisplay Text OFF Output Text SET Triggered Text Exit Port 1 Test Data Capture Register Demo Version ID ExitPort 1 Test Receive RX TestRX / TX Test RX /TX Test DisplayCapture to Port Capture to Memory Dump Memory Exit Capture to PortRX Baudrate Auto TX Baudrate 2400DOWNLOAD/UPLOAD Setup Demo Demo on Power UP OFF ExitVSI-PRO Version 13.00R19 03/25/2008 DOWNLOAD/UPLOAD Data CableDOWNLOAD/UPLOAD Setup Using VSI-PRO to VSI-PRO DOWNLOAD/UPLOAD Setup Using VSI-Pro to VSI-ProDownload Setup Upload Setup Update Firmware Exit Download Setup Upload Setup ExitDOWNLOAD/UPLOAD Setup Using a PC Software InstallationVSI-Pro Remote Program Downloading Ver Click the Tab Remote and you will see the following Menu Figure P2 Remote MenuFile Menu About MenuCommunication Cable Pin Out PC / Laptop VSI-ProVSI-Pro Firmware Download Menu VSI-Pro Firmware Download UtilityFigure P6 Connect To Menu Figure P8 In-System Programming Display Problem Solving Guide Appendix aProblem Solving Guide HOW to do a Master Reset on VSI-PROAppendix a Characters JITTER, JUMP, or SkewPC-BASED Cash Register Appendix BFront Panel TXD RXD GNDAppendix C DVROther Appendix C RS-485 NetworkDB-9 Pin-Out RJ-45 Pin-Out RS-485 Network Data Cable Wiring Electrical CharacteristicsPhysical Characteristics RS-232 ParametersHydra / Regcom Front Panel Hydra / Regcom Rear PanelAppendix D RS-485 NetworkerAppendix F RS-485 VnetworkerAppendix E RS-485 VnetworkerFigure Vnetworker Connection Diagram Vnetworker Software Figure Time / Date Set up Menu Remote Keyboard Vsib Installation Appendix GVsib DB-9M VSI-Pro DB-9M TXD RXD RTS CTS GNDECR Interface Cards Appendix HAppendix Tcpip 232 AdapterTcpip 232 Adapter Tcpip DB-9MHard Alarm Output Appendix JAppendix K VSI-Pro Version 13.00 Register Select MenuRegister Select Appendix KVSI-Pro Version 13.24 Register Select Menu Master Reset Appendix LLimited Warranty Appendix MLimited Warranty Appendix NNorth America