AVE VSI-PRO operation manual Figure P8 In-System Programming Display

Page 54

PROGRAMMING

Second, you go to the menu of the VSI-Pro “Download/Upload Setup” then select ==> “Update Firmware” and then press Set. Now you will see message in Hyper Terminal.

Figure P8 In-System Programming Display

“Do you want to update? [Y/N]” Press “Y” to accept update.

You will see message warning again.

“Doing this will erase the program memory [Y/N]” Press “Y” again to accept update.

NOTE: Pressing “Yes” again will permanently erase the entire program memory and the VSI-Pro will not function until firmware is loaded. Make sure you have the proper firmware file ready or the VSI-Pro will be rendered useless.

Finish erasing the program memory step.

Next, you have to send file to update firmware by click on “Transfer Menu” and select “Send Text File” and wait until finished programming. Progress dots will be displayed on the terminal program until finished and takes approximately 2.5 minutes.

NOTE: If for some reason you are disconnected from the VSI-Pro during downloading, power is lost to the VSI- Pro or PC or the firmware update does not finish for any reason you can repeat the procedure above again. The bootstrap loader never is erased and will always request for a valid firmware update until achieved.

To do this just power up the VSI-Pro or press reset while the terminal program is connected and you will see the prompt messages as above window.

54

Image 54
Contents VSI-PRO JuneVSI-Pro Contents Contents Gasboy Sub-Menu Download/Upload Sub-Menu Introduction VSI / VSI+ / VSI-Pro Backward CompatibilityFeatures & Specifications FeaturesFeatures & Specifications SpecificationsConnections VSI-Pro Rear PanelDTR PIN # Signal Name RS232PIN # Function Direction DSRVSI-PRO VSI-Pro ConnectionsUser Front Panel Controls Front Panel ControlsChanging the Horizontal Position Main Programming Menu ProgrammingGetting Started Register SelectNext page Exit TCP/IP LimitationsDisplay Receipt Exit SET Address ANY ExitSET Address DisplayDevice CON Sole Device Address Exit ModelDisplay Journal Exit DeviceLocal VSS Micros IDN Network Micros ISN Network Exit Operator Customer Combined ExitJournal Receipt Check Credit Exit Device Printer Device Address ANY Modetap ExitWoking Mode Title Display on Console ID ANY Working Mode ExitModel Working Mode Exit NCR Jrnl Printer NCR Rcpt Printer NCR Slip PrinterDevice Address ANY Address Exit Model TK-T500 Mode Emulating ExitDevice Address Exit Next page ExitJournal Printer Receipt Printer SET Term noChoices ALL, 1, 2, 3,..., 253, 254 Choices RECEIPT, CDU 2L , C.D.UScreen Setup Text GrayscaleBackground Grayscale Clock Sub-Menu Title Text DisplayTitler OFF Exit Screen Blank Display Lines Display FormatScreen Blank Choices NONE, 6, 12, 20, 30, 60, 120, 180Line Compress Left JustificationRS-232 CommunicationInterface Type Choices RS-232, Passive TAP, RS-485Choices 7 or Exception ReportsChoices NONE, ODD, Even Exception Report OverviewHard Alarm Output ON-SCREEN FlagsPrinter or DVR Output Total Exception Exception History SET Exception Output Time Stamp ExitException History Total ExceptionsDest ID SCR ID Exit Time Search Time Search SettingDMS-3001 DVR-3011.3021 Choices 1 throughExample 0000.00 Operator None ExitException no History Buffer ON/OFF Scroll Matching Exception Strings ON/OFFProgramming Note Negative ExceptionPage OUT Range Greater thanLess than Exception Report Menu Output Alarm OutputsAlarm no Triggered Text ExitRTS Normal StateChoices no Normally open, NC Normal closed Display Text OFF Output Text SET Triggered Exit Choices 6, 12, 30, 60, 120, 180Triggered Text Display TextDisplay Text OFF Output Text SET Triggered Text Exit TEST/DEMO ModeSET Triggered Text Port 1 Test Data Capture Register Demo Version ID ExitPort 1 Test Receive RX TestRX / TX Test RX /TX Test DisplayRX Baudrate Auto TX Baudrate Capture to Port Capture to Memory Dump Memory ExitCapture to Port 2400VSI-PRO Version 13.00R19 03/25/2008 DOWNLOAD/UPLOAD SetupDemo Demo on Power UP OFF Exit DOWNLOAD/UPLOAD Data CableDOWNLOAD/UPLOAD Setup Using VSI-PRO to VSI-PRO DOWNLOAD/UPLOAD Setup Using VSI-Pro to VSI-ProDownload Setup Upload Setup Update Firmware Exit Download Setup Upload Setup ExitDOWNLOAD/UPLOAD Setup Using a PC Software InstallationVSI-Pro Remote Program Downloading Ver Click the Tab Remote and you will see the following Menu Figure P2 Remote MenuCommunication Cable Pin Out File MenuAbout Menu PC / Laptop VSI-ProVSI-Pro Firmware Download Menu VSI-Pro Firmware Download UtilityFigure P6 Connect To Menu Figure P8 In-System Programming Display Problem Solving Guide Appendix aAppendix a Problem Solving GuideHOW to do a Master Reset on VSI-PRO Characters JITTER, JUMP, or SkewFront Panel PC-BASED Cash RegisterAppendix B TXD RXD GNDAppendix C DVROther Appendix C RS-485 NetworkDB-9 Pin-Out RJ-45 Pin-Out Physical Characteristics RS-485 Network Data Cable WiringElectrical Characteristics RS-232 ParametersHydra / Regcom Front Panel Hydra / Regcom Rear PanelAppendix D RS-485 NetworkerAppendix E Appendix FRS-485 Vnetworker RS-485 VnetworkerFigure Vnetworker Connection Diagram Vnetworker Software Figure Time / Date Set up Menu Remote Keyboard Vsib DB-9M VSI-Pro DB-9M Vsib InstallationAppendix G TXD RXD RTS CTS GNDECR Interface Cards Appendix HTcpip 232 Adapter AppendixTcpip 232 Adapter Tcpip DB-9MHard Alarm Output Appendix JAppendix K VSI-Pro Version 13.00 Register Select MenuRegister Select Appendix KVSI-Pro Version 13.24 Register Select Menu Master Reset Appendix LLimited Warranty Appendix MLimited Warranty Appendix NNorth America