AVE VSI-PRO operation manual VSI-Pro Firmware Download Menu, VSI-Pro Firmware Download Utility

Page 52

PROGRAMMING

VSI-Pro Firmware Download Menu

To update the VSI-Pro, load the VSI-Pro Firmware Download Utility and follow the instructions below. Then select “UPDATE FIRMWARE” from the menu selection.

DOWNLOAD SETUP

UPLOAD SETUP

UPDATE FIRMWARE

EXIT

VSI-Pro Firmware Download Utility

This document describes the VSI-Pro V13.00 Release 12. The new features of this version are able to download firmware update via the RS-232 port. The LDROM 4K boot strap loader must be burner to the uP via a conven- tional programmer. Then the executable program is then loaded via any terminal program such as Hyper Terminal via a PC or compatible device. All firmware files are encoded to the AVE proprietary format and decoded by the bootstrap loader for standard program execution.

Update Firmware of VSI-Pro

You have to connect the VSI-Pro with a Serial Program Terminal such as HyperTerminal, IC etc. But advise to use HyperTerminal.First, you have to set the baud rate HyperTerminal to 19200

See PC Windows below to verify proper HyperTerminal setup.

Figure P5 HyperTerminal Main Menu

52

Image 52

Contents VSI-PRO JuneVSI-Pro Contents Contents Gasboy Sub-Menu Download/Upload Sub-Menu Introduction VSI / VSI+ / VSI-Pro Backward CompatibilityFeatures & Specifications FeaturesFeatures & Specifications SpecificationsConnections VSI-Pro Rear PanelPIN # Signal Name RS232 PIN # Function DirectionDTR DSRVSI-PRO VSI-Pro ConnectionsUser Front Panel Controls Front Panel ControlsChanging the Horizontal Position Programming Getting StartedMain Programming Menu Register SelectNext page Exit TCP/IP LimitationsSET Address ANY Exit SET AddressDisplay Receipt Exit DisplayModel Display Journal ExitDevice CON Sole Device Address Exit DeviceOperator Customer Combined Exit Journal Receipt Check Credit ExitLocal VSS Micros IDN Network Micros ISN Network Exit Device Printer Device Address ANY Modetap ExitTitle Display on Console ID ANY Working Mode Exit Model Working Mode ExitWoking Mode NCR Jrnl Printer NCR Rcpt Printer NCR Slip PrinterModel TK-T500 Mode Emulating Exit Device Address ExitDevice Address ANY Address Exit Next page ExitSET Term no Choices ALL, 1, 2, 3,..., 253, 254Journal Printer Receipt Printer Choices RECEIPT, CDU 2L , C.D.UText Grayscale Screen SetupBackground Grayscale Clock Sub-Menu Text Display Titler OFF ExitTitle Screen Blank Display Lines Display FormatScreen Blank Choices NONE, 6, 12, 20, 30, 60, 120, 180Line Compress Left JustificationCommunication Interface TypeRS-232 Choices RS-232, Passive TAP, RS-485Exception Reports Choices NONE, ODD, EvenChoices 7 or Exception Report OverviewON-SCREEN Flags Hard Alarm OutputPrinter or DVR Output Exception History SET Exception Output Time Stamp Exit Exception HistoryTotal Exception Total ExceptionsTime Search Time Search Setting DMS-3001 DVR-3011.3021Dest ID SCR ID Exit Choices 1 throughExample Operator None Exit 0000.00Exception no History Buffer ON/OFF Scroll Matching Exception Strings ON/OFFProgramming Note Negative ExceptionPage Greater than OUT RangeLess than Alarm Outputs Alarm noException Report Menu Output Triggered Text ExitNormal State RTSChoices no Normally open, NC Normal closed Choices 6, 12, 30, 60, 120, 180 Triggered TextDisplay Text OFF Output Text SET Triggered Exit Display TextTEST/DEMO Mode SET Triggered TextDisplay Text OFF Output Text SET Triggered Text Exit Port 1 Test Data Capture Register Demo Version ID ExitPort 1 Test Receive RX TestRX / TX Test RX /TX Test DisplayCapture to Port Capture to Memory Dump Memory Exit Capture to PortRX Baudrate Auto TX Baudrate 2400DOWNLOAD/UPLOAD Setup Demo Demo on Power UP OFF ExitVSI-PRO Version 13.00R19 03/25/2008 DOWNLOAD/UPLOAD Data CableDOWNLOAD/UPLOAD Setup Using VSI-PRO to VSI-PRO DOWNLOAD/UPLOAD Setup Using VSI-Pro to VSI-ProDownload Setup Upload Setup Update Firmware Exit Download Setup Upload Setup ExitSoftware Installation DOWNLOAD/UPLOAD Setup Using a PCVSI-Pro Remote Program Downloading Ver Click the Tab Remote and you will see the following Menu Figure P2 Remote MenuFile Menu About MenuCommunication Cable Pin Out PC / Laptop VSI-ProVSI-Pro Firmware Download Menu VSI-Pro Firmware Download UtilityFigure P6 Connect To Menu Figure P8 In-System Programming Display Problem Solving Guide Appendix aProblem Solving Guide HOW to do a Master Reset on VSI-PROAppendix a Characters JITTER, JUMP, or SkewPC-BASED Cash Register Appendix BFront Panel TXD RXD GNDDVR Appendix COther RS-485 Network Appendix CDB-9 Pin-Out RJ-45 Pin-Out RS-485 Network Data Cable Wiring Electrical CharacteristicsPhysical Characteristics RS-232 ParametersHydra / Regcom Front Panel Hydra / Regcom Rear PanelAppendix D RS-485 NetworkerAppendix F RS-485 VnetworkerAppendix E RS-485 VnetworkerFigure Vnetworker Connection Diagram Vnetworker Software Figure Time / Date Set up Menu Remote Keyboard Vsib Installation Appendix GVsib DB-9M VSI-Pro DB-9M TXD RXD RTS CTS GNDECR Interface Cards Appendix HAppendix Tcpip 232 AdapterTcpip 232 Adapter Tcpip DB-9MHard Alarm Output Appendix JAppendix K VSI-Pro Version 13.00 Register Select MenuRegister Select Appendix KVSI-Pro Version 13.24 Register Select Menu Master Reset Appendix LLimited Warranty Appendix MLimited Warranty Appendix NNorth America