Atlantis Land A02-RAV211 manual Configure Caller ID info

Page 42

VoIP ROUTER ADSL

Configure Caller ID info:

Modulation: This is Caller ID Modulation (Bell 202.V23). You can select between CID_BELL202 and CID_V23.

Delay: Delay , in milliseconds , between the end of the first ring and beginning of the CID transmission.

FSK AMP 0: FSK (Frequency-Shift Keying) is a method of transmitting digital signals. Logic 0 (low) frequency & logic 1(high) frequency are in an analog form. The VoIP device will convert them to FSK for transmission purpose. Here you can set-up amplitude of logic 0 frequency.

FSK AMP1: Amplitude of logic 1(high) frequency

Configure VAD: VAD (Voice Activity Detection) is a function to detect voice activity during one conversation. It is to efficiently utilize the bandwidth by not transmitting “empty” voice packets when both sides remain silent. In the meantime, a comfort noise could be generated (occupied little bandwidth).

Disable VAD: No VAD function

Enable VAD with Comfort Noise: a comfort noise will be generated (CNG)

Enable VAD with Standard SID: VAD will be done with standard SID (Security Identifier).

Enable VAD and Suppress SID: When silence is detected, the VoIP device will not send any packets to the network and the transmission of packets will be paused until voice is detected again

Configure Echo Cancellation: Four options are available including disable echo cancellation, enable echo cancellation, enable echo cancellation with NLP, enable echo cancellation with CNG_NLP.

Start Attenuation: Setting the Start Attenuation timer.

Max Attenuation: Setting the Max Attenuation timer.

36

Image 42

Contents VoIP Router Adsl Page Important Note CopyrightCE Mark Warning FCC WarningTable of Contents Chapter Chapter Page Introduction An Overview of the VoIP Router AdslPackage Contents VoIP Router Adsl FeaturesPage VoIP Router Adsl Application Front LEDs Rear PortsCabling Before Configuration Connecting the VoIP Router AdslConfiguring PC in Windows For Windows 95/98/MEVoIP Router Adsl For Windows NT4.0 For Windows Click OK to finish the configuration For Windows XP VoIP Router Adsl Factory Default Settings Username and PasswordConfiguring with the Web Browser Information from the ISPStatus Quick StartStatus Adsl Status Adsl Status WAN Status Adsl Status ATM Status Status LAN Status LAN Status TCP StatusStatus- PPP Status Status- Learned MAC TableRouting Table System LogSecurity Logs Quick StartAdsl Quick Start Configuration VoIP Quick StartVoIP System Firewall Virtual Server Advanced 3.1 WAN VoIP Router Adsl Service Category Select UBR or CBR Dhcp Client Static IP SettingsMAC Spoofing 3.2 LAN Device IP Address Dhcp ServerVoIP VoIP Router Adsl AuthorizationUserID Same as UserID Phone Book Call Feature CallWaiting Enable/Disable the call waiting featureCallForwarding Advanced Telephony Settings CallReturn Enable/Disable the call return featureConfigure Caller ID info Echo Cancellation Tail Length Setting the Tail Length Ring & Tone Configuration Timeouts System Password Time ZoneUpgrade Factory SettingRestart Firewall Packet FilteringVoIP Router Adsl Bridge Filtering Intrusion DetectionBlock WAN Request Virtual Server AdvancedAdsl 3.7.2 DNSDynamic DNS 3.7.4 NAT VoIP Router Adsl RIP Default is Disabled Border Gateway Default is Enabled 3.7.5 RIPStatic Route Misc Configuration Dhcp Relay Default at Dhcp Server Dhcp Target IP Default isTesting Ethernet LAN connection Diagnostic TestIgmp Proxy Default at Disabled Testing Adsl SynchronizationTest Ethernet connect to ATM Test ATM OAM Segment Loop BackTest ATM OAM End-to-End Loop Back Test IP connect to PPPSave Config Test Internet connectionProblems with the WAN Interface Problems with the LAN InterfaceProblem Corrective Action Technical Features Appendix B Support