Asante Technologies 35160 Hardware Installation and Setup, Installation Overview, Safety Overview

Page 11

Chapter 2. Hardware Installation and Setup

The following guidelines will help the user to easily install the switch, and to ensure that it has the proper power supply and environment.

2.1 Installation Overview

Follow these steps to install the IntraCore switch:

1.Open the box and check the contents. See Chapter 1.3 Package Contents for a complete list of the items included with the IntraCore switch.

2.Install the switch in an equipment or wall rack, or prepare it for desktop placement.

3.Connect the power cord to the unit and to an appropriate power source.

4.Connect network devices to the switch.

See the sections below for more detailed installation instructions.

2.1.1 Safety Overview

The following information provides safety guidelines to ensure the user’s safety and to protect the switch from damage.

Note: This information is intended as a guideline, and may not include every possible hazard to which the user may be exposed. Use caution when installing this switch.

•Only trained and qualified personnel should be allowed to install or replace this equipment

•Always use caution when lifting heavy equipment

•Keep the unit clean

•Keep tools and components off the floor and away from foot traffic

•Avoid wearing rings or chains (or other jewelry) that could get caught in the switch. Metal objects can heat up and cause serious injury to persons and damage to the equipment. Avoid wearing loose clothing (such as ties or loose sleeves) when working around the switch

When working with electricity, follow these guidelines:

•Disconnect all external cables before installing or removing the cover

•Do not work alone when working with electricity

•Always check that the cord has been disconnected from the outlet before performing hardware configuration

•Do not tamper with the equipment. Doing so could void the warranty

•Examine the work area for potential hazards (such as wet floors or ungrounded cables)

2.1.2 Recommended Installation Tools

You will need the following tools and equipment (not included) to install the switch into an equipment rack:

• Flat head screwdriver

• Phillips head screwdriver

• Antistatic mat or foam

11

Image 11

Contents IntraCore 35160 Series Quick Start Guide IntraCore 35160 Series Layer 2 Gigabit Switches User’s ManualTable of Contents Page Introduction FeaturesLEDs SwitchCore CXE2010Package Contents 2 IC35160-G 1 IC35160-TFront and Back Panel Descriptions Management and ConfigurationSnmp Management Console InterfaceWeb-Based Interface Recommended Installation Tools Hardware Installation and SetupInstallation Overview Safety OverviewCooling and Airflow Installation into an Equipment RackPower Requirements Environmental RequirementsGbic Interfaces Installing a GbicGbic Care and Handling Installing the Optional Emergency Power SupplyConnecting Power Removing a Gbic1 10/100/1000BaseT Ports Cabling Procedures Connecting to the NetworkConnecting to a Console SetupGigabit Ethernet Ports Cabling Procedures Connecting Via Telnet Connecting Via the Web BrowserIP Assignment Changing the PasswordSimple Network Management Protocol Snmp Exiting a Submenu ConfigurationAccessing a Submenu LoggingGeneral Information Configuration MenuChanging System Administration Info Administration ConfigurationChanging System IP Information System IP ConfigurationPort Configuration Page Enabling or Disabling a Port Advanced Port ConfigurationEnabling or Disabling 802.3x Flow Control Setting Port Class of ServiceSetting Port Default Priority Setting Port Maximum Packet LengthGlobal Port Configuration Unicast Forwarding Database ConfigurationDisplaying the Forwarding Database Searching for a MAC Address Setting the MAC Address Age-Out TimeSecurity Management Vlan ManagementChanging Community Strings Protocol ConfigurationSnmp Configuration Adding or Updating a Trap Receiver Enabling Authentication TrapsDeleting a Trap Receiver Spanning Tree Protocol STP ConfigurationEnabling and Disabling STP Spanning Tree Port ConfigurationSetting Port Priority and Path Cost Trunk Group Configuration Assigning Packets to Priority Queues QoS Priority Queue ManagementDefining the Priority List Example Setting SSH/Telnet UI Time-out User Interface ConfigurationSetting Console UI Time-out Period Enabling or Disabling SSH and Telnet Change PasswordAdding or Deleting an Access Host Enabling or Disabling the Web Server Access ControlSystem Utilities Adding or Deleting a Monitor Port Port MirroringEnabling or Disabling System Port Mirroring System Clock System ResetResetting the Switch System Log Scheduling a System ResetClearing the System Log Bootstrap ConfigurationTftp File Transfers Ping Utility StatisticsRmon Management Advanced ManagementSnmp and Rmon Management Viewing a List of Duplicated IP Addresses Duplicated IP Detection and TrapEnabling and Disabling Duplicated IP Detection Enabling and Disabling Duplicated IP TrapEnabling and Disabling Station Movement Trap Configuring Port SecurityConfiguring Port Lock and Intruder Lock Configuring Port New Node Detection TrapResetting Security to Defaults Port-based Network Access ControlConfiguring Security Level 2 or Level Setting the Intruder TrapPage Name Description Port Control SettingsSetting Timers Server Port Setting Radius ParametersRadius Server IP Vlan Management Vlan Specifications for the IntraCore 35160 SeriesOther Vlan Features of the switch Creating a Vlan Configuring Static Vlan GroupsAdvanced Static Vlan Configuration Adding and Deleting VLANs from the Port Configuring Vlan Port AttributesSetting the Port Vlan ID Configuring Port Receive Frame TypeDisplaying a Summary of Vlan Groups Setting Port TypeMulticast Addresses Resetting Vlan Configuration to DefaultsIP Multicast Traffic Management Displaying a Vlan Port SummaryEnabling and Disabling Igmp Snooping Configuring IP Multicast Traffic ManagementIgmp Snooping Displaying a Summary of Group Addresses Advanced Igmp ConfigurationRemoving a Multicast Group Address IP Multicast Forwarding Database ConfigurationAdding Ports to the Selected Address Inserting a Multicast Group AddressWeb-Based Management Accessing with a Web BrowserManagement Buttons Front Panel ButtonGenl Info General Information Button Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp ButtonVlan Group Create Vlan ConfigurationVlan Button Acceptable Frame Type Port ConfigurationSet Port Type Port Vlan ID PvidTag/Untag Port Egress Type Trunking ButtonSecurity Button Port Ingress FilteringPage Snmp Protocol Snmp ManagementSnmp Management Operations Name Space Path Community Name and SecurityMIB Tree MIB Groups Supported Vlan ID and Tagged Frames Switching ConceptsVLANs Port-Based VLANsSpanning Tree Parameters Spanning Tree ProtocolPort Vlan ID How It WorksFull Duplex Spanning Tree Port ConfigurationFull Duplex, Flow Control, and Auto-negotiation Auto-Negotiation Flow ControlProblem Possible Solutions Appendix A. TroubleshootingPhysical Characteristics Appendix B. Features and SpecificationsSpecifications Standards Compliance Technical Support and WarrantyEnvironmental Range IntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration Loading Software Locally Appendix F. BootP ConfigurationBootstrap Configuration Image BanksLoading Software Remotely BOOTP-TFTP