Asante Technologies 35160 Unicast Forwarding Database Configuration, Global Port Configuration

Page 27

The new maximum packet length is shown on the Advanced Port Configuration Menu.

3.6.5 Global Port Configuration

The Global Port Configuration Menu allows the user to simultaneously change the configuration information for all ports.

To change the port configuration for all ports, use the following procedure:

1.From the Configuration Menu, type p to access the Port Configuration Menu.

2.From the Basic Port Configuration Menu, type g. The Global Port Configuration Menu appears, as shown below.

IntraCore 35160-T Global Port Configuration Menu

		1	8	9	16
Operating Status:		========		========
		--------		-++---+-
Auto Negotiation:		********		********
Speed/Duplex:		GGGGGGGG		GGFGGGHG
Flow Ctrl:		--------		--------
Class Of Service:		********		********
Priority:		00000000		00000000
<Cmd>	<Description>
t	Select Global Port Status Enable/Disable

aSelect Global Auto-Negotiation Enable/Disable

l Select Global 10/100/1000 Mbps Link Speed

d Select Global Half/Full Duplex

f Toggle Global Flow Control Enable/Disable

c Toggle Global Class Of Service (COS) Enable/Disable

i Set Global Port Default Priority

m Set MAX Packet Length

q Return to previous menu

root>

3.Type the corresponding command letter to configure the desired feature(s). The change is reflected immediately in the Global Port Configuration Menu.

3.7Unicast Forwarding Database Configuration

The Unicast Forwarding Database Configuration Menu allows the user to view and search for addresses in the MAC (Media Access Control) Forwarding Table on the switch. It also provides options for displaying MAC addresses and IP/MAC binding by individual port or by VLAN.

The MAC Forwarding Table is a table of node addresses that the switch automatically builds by “learning.” It performs this task by monitoring the packets that pass through the switch, checking the source and destination addresses, and then recording the source address information in the table.

The switch uses the information in this table to decide whether a frame should be forwarded to a particular destination port or “flooded” to all ports other than to the received port. Each entry consists of three parts: the MAC address of the device, the port number on which it was received, and the VLAN number.

Note: The MAC address table can hold a maximum of 8,192 entries.

27

Image 27

Contents IntraCore 35160 Series Quick Start Guide IntraCore 35160 Series Layer 2 Gigabit Switches User’s ManualTable of Contents Page Introduction FeaturesSwitchCore CXE2010 Package ContentsLEDs 2 IC35160-G 1 IC35160-TFront and Back Panel Descriptions Management and ConfigurationConsole Interface Web-Based InterfaceSnmp Management Recommended Installation Tools Hardware Installation and SetupInstallation Overview Safety OverviewCooling and Airflow Installation into an Equipment RackPower Requirements Environmental RequirementsGbic Interfaces Installing a GbicGbic Care and Handling Installing the Optional Emergency Power SupplyConnecting Power Removing a Gbic1 10/100/1000BaseT Ports Cabling Procedures Connecting to the NetworkSetup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console Connecting Via Telnet Connecting Via the Web BrowserIP Assignment Changing the PasswordSimple Network Management Protocol Snmp Exiting a Submenu ConfigurationAccessing a Submenu LoggingGeneral Information Configuration MenuChanging System Administration Info Administration ConfigurationSystem IP Configuration Port ConfigurationChanging System IP Information Page Enabling or Disabling a Port Advanced Port ConfigurationEnabling or Disabling 802.3x Flow Control Setting Port Class of ServiceSetting Port Default Priority Setting Port Maximum Packet LengthGlobal Port Configuration Unicast Forwarding Database ConfigurationDisplaying the Forwarding Database Searching for a MAC Address Setting the MAC Address Age-Out TimeSecurity Management Vlan ManagementProtocol Configuration Snmp ConfigurationChanging Community Strings Adding or Updating a Trap Receiver Enabling Authentication TrapsDeleting a Trap Receiver Spanning Tree Protocol STP ConfigurationSpanning Tree Port Configuration Setting Port Priority and Path CostEnabling and Disabling STP Trunk Group Configuration QoS Priority Queue Management Defining the Priority ListAssigning Packets to Priority Queues Example User Interface Configuration Setting Console UI Time-out PeriodSetting SSH/Telnet UI Time-out Change Password Adding or Deleting an Access HostEnabling or Disabling SSH and Telnet Access Control System UtilitiesEnabling or Disabling the Web Server Port Mirroring Enabling or Disabling System Port MirroringAdding or Deleting a Monitor Port System Reset Resetting the SwitchSystem Clock System Log Scheduling a System ResetClearing the System Log Bootstrap ConfigurationTftp File Transfers Ping Utility StatisticsAdvanced Management Snmp and Rmon ManagementRmon Management Viewing a List of Duplicated IP Addresses Duplicated IP Detection and TrapEnabling and Disabling Duplicated IP Detection Enabling and Disabling Duplicated IP TrapEnabling and Disabling Station Movement Trap Configuring Port SecurityConfiguring Port Lock and Intruder Lock Configuring Port New Node Detection TrapResetting Security to Defaults Port-based Network Access ControlConfiguring Security Level 2 or Level Setting the Intruder TrapPage Name Description Port Control SettingsSetting Timers Setting Radius Parameters Radius Server IPServer Port Vlan Specifications for the IntraCore 35160 Series Other Vlan Features of the switchVlan Management Creating a Vlan Configuring Static Vlan GroupsAdvanced Static Vlan Configuration Adding and Deleting VLANs from the Port Configuring Vlan Port AttributesSetting the Port Vlan ID Configuring Port Receive Frame TypeDisplaying a Summary of Vlan Groups Setting Port TypeMulticast Addresses Resetting Vlan Configuration to DefaultsIP Multicast Traffic Management Displaying a Vlan Port SummaryConfiguring IP Multicast Traffic Management Igmp SnoopingEnabling and Disabling Igmp Snooping Displaying a Summary of Group Addresses Advanced Igmp ConfigurationRemoving a Multicast Group Address IP Multicast Forwarding Database ConfigurationAdding Ports to the Selected Address Inserting a Multicast Group AddressWeb-Based Management Accessing with a Web BrowserFront Panel Button Genl Info General Information ButtonManagement Buttons Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp ButtonVlan Configuration Vlan ButtonVlan Group Create Acceptable Frame Type Port ConfigurationSet Port Type Port Vlan ID PvidTag/Untag Port Egress Type Trunking ButtonSecurity Button Port Ingress FilteringPage Snmp Management Snmp Management OperationsSnmp Protocol Community Name and Security MIB TreeName Space Path MIB Groups Supported Vlan ID and Tagged Frames Switching ConceptsVLANs Port-Based VLANsSpanning Tree Parameters Spanning Tree ProtocolPort Vlan ID How It WorksSpanning Tree Port Configuration Full Duplex, Flow Control, and Auto-negotiationFull Duplex Auto-Negotiation Flow ControlProblem Possible Solutions Appendix A. TroubleshootingAppendix B. Features and Specifications SpecificationsPhysical Characteristics Technical Support and Warranty Environmental RangeStandards Compliance Appendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration Loading Software Locally Appendix F. BootP ConfigurationBootstrap Configuration Image BanksLoading Software Remotely BOOTP-TFTP