Asante Technologies 35160 user manual Setting Timers

Page 53

Setting Timers

To set the timing parameters, type t in the 802.1X Configuration Menu. After changing any of the parameters listed below, the change will be noted in the top of the menu screen.

IntraCore 35160-T 802.1X Constant Configuration Menu

Quiet-period <0..65535,default=60>		: 60
Tx-period <0..65535,default=30>		: 30
Supplicant-timeout <1..300,default=30>		: 30
Server-timeout <1..300,default=30>		: 30
MaxReq <1..10,default=2>		: 2
ReAuthMax <1..10,default=2>		: 2
ReAuth-period <1..N,default=3600>		: 3600
<Cmd>	<Description>
e	Quiet-period
t	Tx-period
p	Supplicant-timeout
s	Server-timeout
m	MaxReq
a	ReAuthMax
r	Reauth-period

qReturn to previous menu

root>

The Quiet-period is the time the authenticator (the IC35160) will wait, if the client is not successfully authenticated, before allowing the client to try again. The default is set to 60 seconds. To adjust the quiet- period, type e in the Constant Configuration Menu.

The Tx-period is the time the authenticator will wait, while waiting for response to identity request, before retransmitting the identity request message. The default is set to 30 seconds. To adjust the Tx-period, type t in the Constant Configuration Menu.

The Supplicant-timeout is the time the authenticator must wait before determining that timeout is occurred while waiting for client response. The default is set to 30 seconds. To adjust the Supplicant-timeout, type p in the Constant Configuration Menu.

The Server-timeout is the time the authenticator must wait before determining that timeout is occurred while waiting for the authentication server response. The default is set to 30 seconds. To adjust the Server- timeout, type s in the Constant Configuration Menu.

The MaxReq is the maximum number of times used to re-transmit a request message to the client before it times out. The default value is 2 times. To adjust the MaxReq value, type m in the Constant Configuration Menu.

The ReAuthMax is the number of re-authentication attempts that are permitted before the authorized client becomes unauthorized. The default value is 2 attempts. To adjust the ReAuthMax value, type a in the Constant Configuration Menu.

The ReAuth-period is the time used by authenticator to determine when re-authentication of the client takes place. The default is set to 3600 seconds. To adjust the ReAuth-period, type r in the Constant Configuration Menu.

53

Image 53

Contents IntraCore 35160 Series Quick Start Guide IntraCore 35160 Series Layer 2 Gigabit Switches User’s ManualTable of Contents Page Introduction FeaturesLEDs SwitchCore CXE2010Package Contents 2 IC35160-G 1 IC35160-TFront and Back Panel Descriptions Management and ConfigurationSnmp Management Console InterfaceWeb-Based Interface Installation Overview Hardware Installation and SetupSafety Overview Recommended Installation ToolsPower Requirements Installation into an Equipment RackEnvironmental Requirements Cooling and AirflowGbic Interfaces Installing a GbicConnecting Power Installing the Optional Emergency Power SupplyRemoving a Gbic Gbic Care and Handling1 10/100/1000BaseT Ports Cabling Procedures Connecting to the NetworkConnecting to a Console SetupGigabit Ethernet Ports Cabling Procedures Connecting Via Telnet Connecting Via the Web BrowserIP Assignment Changing the PasswordSimple Network Management Protocol Snmp Accessing a Submenu ConfigurationLogging Exiting a SubmenuGeneral Information Configuration MenuChanging System Administration Info Administration ConfigurationChanging System IP Information System IP ConfigurationPort Configuration Page Enabling or Disabling a Port Advanced Port ConfigurationSetting Port Default Priority Setting Port Class of ServiceSetting Port Maximum Packet Length Enabling or Disabling 802.3x Flow ControlGlobal Port Configuration Unicast Forwarding Database ConfigurationDisplaying the Forwarding Database Security Management Setting the MAC Address Age-Out TimeVlan Management Searching for a MAC AddressChanging Community Strings Protocol ConfigurationSnmp Configuration Adding or Updating a Trap Receiver Enabling Authentication TrapsDeleting a Trap Receiver Spanning Tree Protocol STP ConfigurationEnabling and Disabling STP Spanning Tree Port ConfigurationSetting Port Priority and Path Cost Trunk Group Configuration Assigning Packets to Priority Queues QoS Priority Queue ManagementDefining the Priority List Example Setting SSH/Telnet UI Time-out User Interface ConfigurationSetting Console UI Time-out Period Enabling or Disabling SSH and Telnet Change PasswordAdding or Deleting an Access Host Enabling or Disabling the Web Server Access ControlSystem Utilities Adding or Deleting a Monitor Port Port MirroringEnabling or Disabling System Port Mirroring System Clock System ResetResetting the Switch System Log Scheduling a System ResetClearing the System Log Bootstrap ConfigurationTftp File Transfers Ping Utility StatisticsRmon Management Advanced ManagementSnmp and Rmon Management Enabling and Disabling Duplicated IP Detection Duplicated IP Detection and TrapEnabling and Disabling Duplicated IP Trap Viewing a List of Duplicated IP AddressesEnabling and Disabling Station Movement Trap Configuring Port SecurityConfiguring Port Lock and Intruder Lock Configuring Port New Node Detection TrapConfiguring Security Level 2 or Level Port-based Network Access ControlSetting the Intruder Trap Resetting Security to DefaultsPage Name Description Port Control SettingsSetting Timers Server Port Setting Radius ParametersRadius Server IP Vlan Management Vlan Specifications for the IntraCore 35160 SeriesOther Vlan Features of the switch Creating a Vlan Configuring Static Vlan GroupsAdvanced Static Vlan Configuration Setting the Port Vlan ID Configuring Vlan Port AttributesConfiguring Port Receive Frame Type Adding and Deleting VLANs from the PortDisplaying a Summary of Vlan Groups Setting Port TypeIP Multicast Traffic Management Resetting Vlan Configuration to DefaultsDisplaying a Vlan Port Summary Multicast AddressesEnabling and Disabling Igmp Snooping Configuring IP Multicast Traffic ManagementIgmp Snooping Displaying a Summary of Group Addresses Advanced Igmp ConfigurationAdding Ports to the Selected Address IP Multicast Forwarding Database ConfigurationInserting a Multicast Group Address Removing a Multicast Group AddressWeb-Based Management Accessing with a Web BrowserManagement Buttons Front Panel ButtonGenl Info General Information Button Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp ButtonVlan Group Create Vlan ConfigurationVlan Button Set Port Type Port ConfigurationPort Vlan ID Pvid Acceptable Frame TypeSecurity Button Trunking ButtonPort Ingress Filtering Tag/Untag Port Egress TypePage Snmp Protocol Snmp ManagementSnmp Management Operations Name Space Path Community Name and SecurityMIB Tree MIB Groups Supported VLANs Switching ConceptsPort-Based VLANs Vlan ID and Tagged FramesPort Vlan ID Spanning Tree ProtocolHow It Works Spanning Tree ParametersFull Duplex Spanning Tree Port ConfigurationFull Duplex, Flow Control, and Auto-negotiation Auto-Negotiation Flow ControlProblem Possible Solutions Appendix A. TroubleshootingPhysical Characteristics Appendix B. Features and SpecificationsSpecifications Standards Compliance Technical Support and WarrantyEnvironmental Range IntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration Bootstrap Configuration Appendix F. BootP ConfigurationImage Banks Loading Software LocallyLoading Software Remotely BOOTP-TFTP