Asante Technologies 35160 user manual Configuring Static Vlan Groups, Creating a Vlan

Page 56

IntraCore	35160-T VLAN Management Menu
VLAN Version:		1	VLAN Type:	Port Based
Max. Supported VLAN ID:		4094	Max. Supported VLANs:	1024
Number of VLANs Configured:		64	Number of Active VLANs:	64
<Cmd>	<Description>
v	VLAN Group Static Configuration
p	VLAN Port Attribute Configuration
d	Display VLAN Groups Summary		Summary
a	Display Port VLAN Attribute		Summary
r	Reset VLAN Configuration to		Factory Default
q	Return to previous menu

Command>

4.3.2 Configuring Static VLAN Groups

To access the VLAN Group Static Configuration Menu, type v in the Configuration Menu to access the VLAN Management Menu, then type v again to access the VLAN Group Static Configuration Menu. A screen similar to the following appears:

IntraCore	35160-T VLAN Group Static Configuration						Menu	VID:[0001]
Name: Default VLAN						Created By: Mgmt
Mgm Access: Enable			8	Status: Active
	Port List 1			9	16
		========		========		+: static
		++++++++		++++++++				d: dynamic

								-: Not Member
<Cmd>	<Description>					<Cmd>	<Description>
c	Create VLAN					r	Remove VLAN
e	Set VLAN Name					t	Toggle Mgmt Access
m	Move ports to this VLAN					d	Delete Port Members
o	Overlap Ports To This Vlan					f	Display Vlan-Grp Information
l	Toggle To Vlan-prt Config Menu
Command>		N)ext VLAN		P)rev VLAN		H)elp		Q)uit
S)elect VID

Navigate to the desired VLAN to configure by typing a command (s, n, or p) as shown at the bottom of the screen. With the Select command, select a VLAN by its VLAN ID (VID); type the VID of an existing VLAN, or the VID of a VLAN you will create.

Creating a VLAN

Follow the steps below to create a new VLAN:

1.Type c from the VLAN Group Static Configuration Menu.

2.Type s to select the VLAN, and then enter the VLAN ID (VID) that has been chosen for use. Notice that the VID for an unused VLAN is 0000.

3.Press Enter.

4.Type e to set the VLAN name (up to 32 characters) and press Enter.

5.Type m to select the ports to be assigned the VLAN.

To make more than one assignment, separate each one with a comma. For example, 8,11 specifies ports 8 and 11. To specify a range of ports, use a hyphen. For example, 1-3, 8, 11 specifies ports 1, 2, 3, 8, and 11. See Help for more information about specifying units and ports.

56

Image 56

Contents IntraCore 35160 Series Quick Start Guide Layer 2 Gigabit Switches User’s Manual IntraCore 35160 SeriesTable of Contents Page Features IntroductionLEDs SwitchCore CXE2010Package Contents 1 IC35160-T 2 IC35160-GManagement and Configuration Front and Back Panel DescriptionsSnmp Management Console InterfaceWeb-Based Interface Hardware Installation and Setup Installation OverviewSafety Overview Recommended Installation ToolsInstallation into an Equipment Rack Power RequirementsEnvironmental Requirements Cooling and AirflowInstalling a Gbic Gbic InterfacesInstalling the Optional Emergency Power Supply Connecting PowerRemoving a Gbic Gbic Care and HandlingConnecting to the Network 1 10/100/1000BaseT Ports Cabling ProceduresConnecting to a Console SetupGigabit Ethernet Ports Cabling Procedures Connecting Via the Web Browser Connecting Via TelnetChanging the Password IP AssignmentSimple Network Management Protocol Snmp Configuration Accessing a SubmenuLogging Exiting a SubmenuConfiguration Menu General InformationAdministration Configuration Changing System Administration InfoChanging System IP Information System IP ConfigurationPort Configuration Page Advanced Port Configuration Enabling or Disabling a PortSetting Port Class of Service Setting Port Default PrioritySetting Port Maximum Packet Length Enabling or Disabling 802.3x Flow ControlUnicast Forwarding Database Configuration Global Port ConfigurationDisplaying the Forwarding Database Setting the MAC Address Age-Out Time Security ManagementVlan Management Searching for a MAC AddressChanging Community Strings Protocol ConfigurationSnmp Configuration Enabling Authentication Traps Adding or Updating a Trap ReceiverSpanning Tree Protocol STP Configuration Deleting a Trap ReceiverEnabling and Disabling STP Spanning Tree Port ConfigurationSetting Port Priority and Path Cost Trunk Group Configuration Assigning Packets to Priority Queues QoS Priority Queue ManagementDefining the Priority List Example Setting SSH/Telnet UI Time-out User Interface ConfigurationSetting Console UI Time-out Period Enabling or Disabling SSH and Telnet Change PasswordAdding or Deleting an Access Host Enabling or Disabling the Web Server Access ControlSystem Utilities Adding or Deleting a Monitor Port Port MirroringEnabling or Disabling System Port Mirroring System Clock System ResetResetting the Switch Scheduling a System Reset System LogBootstrap Configuration Clearing the System LogTftp File Transfers Statistics Ping UtilityRmon Management Advanced ManagementSnmp and Rmon Management Duplicated IP Detection and Trap Enabling and Disabling Duplicated IP DetectionEnabling and Disabling Duplicated IP Trap Viewing a List of Duplicated IP AddressesConfiguring Port Security Enabling and Disabling Station Movement TrapConfiguring Port New Node Detection Trap Configuring Port Lock and Intruder LockPort-based Network Access Control Configuring Security Level 2 or LevelSetting the Intruder Trap Resetting Security to DefaultsPage Port Control Settings Name DescriptionSetting Timers Server Port Setting Radius ParametersRadius Server IP Vlan Management Vlan Specifications for the IntraCore 35160 SeriesOther Vlan Features of the switch Configuring Static Vlan Groups Creating a VlanAdvanced Static Vlan Configuration Configuring Vlan Port Attributes Setting the Port Vlan IDConfiguring Port Receive Frame Type Adding and Deleting VLANs from the PortSetting Port Type Displaying a Summary of Vlan GroupsResetting Vlan Configuration to Defaults IP Multicast Traffic ManagementDisplaying a Vlan Port Summary Multicast AddressesEnabling and Disabling Igmp Snooping Configuring IP Multicast Traffic ManagementIgmp Snooping Advanced Igmp Configuration Displaying a Summary of Group AddressesIP Multicast Forwarding Database Configuration Adding Ports to the Selected AddressInserting a Multicast Group Address Removing a Multicast Group AddressAccessing with a Web Browser Web-Based ManagementManagement Buttons Front Panel ButtonGenl Info General Information Button Port Config Port Configuration Button Span Tree Spanning Tree Button Snmp Button Addr Address Table ButtonVlan Group Create Vlan ConfigurationVlan Button Port Configuration Set Port TypePort Vlan ID Pvid Acceptable Frame TypeTrunking Button Security ButtonPort Ingress Filtering Tag/Untag Port Egress TypePage Snmp Protocol Snmp ManagementSnmp Management Operations Name Space Path Community Name and SecurityMIB Tree MIB Groups Supported Switching Concepts VLANsPort-Based VLANs Vlan ID and Tagged FramesSpanning Tree Protocol Port Vlan IDHow It Works Spanning Tree ParametersFull Duplex Spanning Tree Port ConfigurationFull Duplex, Flow Control, and Auto-negotiation Flow Control Auto-NegotiationAppendix A. Troubleshooting Problem Possible SolutionsPhysical Characteristics Appendix B. Features and SpecificationsSpecifications Standards Compliance Technical Support and WarrantyEnvironmental Range IntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Pin Number Signal Name Appendix D. Console Port Pin OutsAppendix E. Online Warranty Registration Appendix F. BootP Configuration Bootstrap ConfigurationImage Banks Loading Software LocallyBOOTP-TFTP Loading Software Remotely