Motorola MVME197LE manual

Page 6

2.Although not shown in the above list, each Motorola Computer Group manual publication number is suffixed with characters which represent the revision level of the document, such as “/D2” (the second revision of a manual); a supplement bears the same number as the manual but has a suffix such as “/A1” (the first supplement to the manual).

To further assist your development effort, Motorola has collected user’s manuals for each of the peripheral controllers used on the MVME197 module series and other boards from the suppliers. This bundle includes manuals for the following:

68-1X7DSfor use with the MVME197 series of Single Board Computers.

NCR 53C710 SCSI Controller Data Manual and Programmer’s Guide Intel i82596 Ethernet Controller User’s Manual

Cirrus Logic CD2401 Serial Controller User’s Manual SGS-Thompson MK48T08 NVRAM/TOD Clock Data Sheet

The following non-Motorola publications may also be of interest and may be obtained from the sources indicated. The VMEbus Specification is contained in ANSI/IEEE Standard 1014-1987.

ANSI/IEEE Std 1014-1987

The Institute of Electrical and Electronics

Versatile Backplane Bus: VMEbus

Engineers, Incorporated

 

Publication and Sales Department

 

345 East 47th Street

 

New York, New York 10017-2633

 

Telephone: 1-800-678-4333

ANSI Small Computer System Interface-2

Global Engineering Documents

(SCSI-2), Draft Document X3.131-198X,

P.O. Box 19539

Revision 10c

Irvine, California 92713-9539

 

Telephone (714) 979-8135

Image 6
Contents MVME197LE Restricted Rights Legend Preface Document TerminologyBIT Related Documentation Document Title Motorola Publication NumberPage Page Safety Summary Safety Depends on YOU Contents Hardware Preparation and Installation Using the 197Bug Debugger Appendix a Configure and Environment Commands List of Figures Xiv List of Tables Xvi Introduction OverviewRequirements Features Specifications Block DiagramMVME197LE Specifications Block Diagram Mezzanine Address Bus Bus Data Bus 256 BusSwitchMC88110 Address Data MUX Address Memory ArrayFront Panel Switches and Indicators Functional DescriptionFlash Memory Data Bus StructureMC88110 MPU Onboard DramInterfaces Battery Backup RAM and ClockVMEbus Interface Serial Port InterfacePrinter Interface Ethernet InterfaceScsi Interface Scsi TerminationPeripheral Resources Interrupt Sources ConnectorsMemory Maps Processor Bus Memory MapProcessor Bus Memory Map DramsizeAddress Range Devices Accessed Port Size Local Devices Memory MapVMEbus Accesses to the Local Peripheral Bus VMEbus Memory MapVMEbus Short I/O Memory Map Unpacking Instructions Hardware PreparationHardware Preparation and Installation VMEbus Connector P1 Configuration Switches Switch S1Configuration Switch S1 General Information S1-1 to S1-8 OFF -- All Ones Factory Configuration Installation Instructions Switch S6MVME197LE Module Installation System Considerations MVME197LEIG/D1 Hardware Preparation and Installation Overview of M88000 Firmware Description of 197BugInstallation and Start-up Comparison With M68000-Based Firmware197Bug Implementation Terminal to make sure XON/XOFF handshaking is enabled OteAutoboot ROMboot Network BootReset Restarting the SystemAbort BreakMemory Requirements SYSFAIL* Assertion/NegationMPU Clock Speed Calculation Terminal Input/Output Control DELDisk I/O Support Blocks Versus SectorsDevice Probe Function Disk I/O via 197Bug Commands Disk I/O via 197Bug System Calls DskcfigDefault 197Bug Controller and Device Parameters Disk I/O Error CodesNetwork I/O Support UDP/IP Protocol Modules Bootp Protocol ModulePhysical Layer Manager Ethernet Driver RARP/ARP Protocol ModulesMultiprocessor Support Network Boot Control ModuleNetwork I/O Error Codes Multiprocessor Control Register Mpcr MethodMpar Diagnostic Facilities Gcsr MethodDebugger General Information Entering Debugger Command Lines DebuggerSyntactic Variables Expression as a ParameterData Type Base Identifier Examples Address as a Parameter Address FormatsOffset Registers Entering and Debugging Programs Port Numbers197Bug Vector Table and Workspace Calling System Utilities From User ProgramsPreserving The Debugger Operating Environment Hardware FunctionsFloating Point Support CPU/MPU RegistersSingle Precision Real Double Precision RealScientific Notation 197Bug Debugger Command Set Debugger CommandsNocm Noma Name Nioc RL Addrbhw Using the 197Bug Debugger Configure Board Information Block Cnfg MISet Environment to Bug/Operating System ENV DTable A-1. ENV Command Parameters ENV Parameter and Options Default Meaning of DefaultConfigure and Environment Commands Ffbffffc Table A-1. ENV Command Parameters Memory Requirement s 01FFFFFF Table A-1. ENV Command Parameters Efffffff FF7FFFFF Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters DISK/TAPE Controller Data Disk/Tape Controller Modules SupportedMVME320 4 Devices Disk/Tape Controller Default ConfigurationsSingle Board Computers 7 Devices MVME323 4 DevicesMVME327A 9 Devices MVME328 14 DevicesMVME350 1 Device IOT Command Parameters for Supported Floppy Types IOT ParameterDisk/Tape Controller Data Network Controller Data Network Controller Modules SupportedNetwork Controller Data Symbols NumericsIN-2 IN-3 Nvram A-2 XON/XOFF Index
Related manuals
Manual 78 pages 27.46 Kb