Motorola MVME197LE manual

Page 7

The computer programs stored in the Read Only Memory of this device contain material copyrighted by Motorola Inc., first published 1991, and may be used only under license such as the License for Computer Programs (Article 14) contained in Motorola’s Terms and Conditions of Sale, Rev. 1/79.

Motorola® and the Motorola symbol are registered trademarks of Motorola, Inc.

Delta Series, M88000, SYSTEM V/88, VMEmodule, VMEsystem, and197bug are trademarks of Motorola, Inc.

Timekeeper and Zeropower are trademarks of Thompson Components.

All other products mentioned in this document are trademarks or registered trademarks of their respective holders

© Copyright Motorola 1993

All Rights Reserved

Printed in the United States of America

September 1993

!

WARNING

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the documentation for this product, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A Computing Device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at the user’s own expense, will be required to take whatever measures necessary to correct the interference.

Image 7

Contents MVME197LE Restricted Rights Legend Document Terminology PrefaceBIT Document Title Motorola Publication Number Related DocumentationPage Page Safety Summary Safety Depends on YOU Contents Hardware Preparation and Installation Using the 197Bug Debugger Appendix a Configure and Environment Commands List of Figures Xiv List of Tables Xvi Overview IntroductionRequirements Features Block Diagram SpecificationsMVME197LE Specifications Block Diagram Memory Array Bus Data Bus 256 BusSwitchMC88110 Address Data MUX Address Mezzanine Address BusFunctional Description Front Panel Switches and IndicatorsOnboard Dram Data Bus StructureMC88110 MPU Flash MemorySerial Port Interface Battery Backup RAM and ClockVMEbus Interface InterfacesEthernet Interface Printer InterfaceScsi Termination Scsi InterfacePeripheral Resources Processor Bus Memory Map ConnectorsMemory Maps Interrupt SourcesDramsize Processor Bus Memory MapLocal Devices Memory Map Address Range Devices Accessed Port SizeVMEbus Memory Map VMEbus Accesses to the Local Peripheral BusVMEbus Short I/O Memory Map Hardware Preparation Unpacking InstructionsHardware Preparation and Installation VMEbus Connector P1 Switch S1 Configuration SwitchesConfiguration Switch S1 General Information S1-1 to S1-8 OFF -- All Ones Factory Configuration Switch S6 Installation InstructionsMVME197LE Module Installation System Considerations MVME197LEIG/D1 Hardware Preparation and Installation Description of 197Bug Overview of M88000 FirmwareComparison With M68000-Based Firmware Installation and Start-up197Bug Implementation Ote Terminal to make sure XON/XOFF handshaking is enabledAutoboot Network Boot ROMbootRestarting the System ResetBreak AbortSYSFAIL* Assertion/Negation Memory RequirementsMPU Clock Speed Calculation DEL Terminal Input/Output ControlBlocks Versus Sectors Disk I/O SupportDevice Probe Function Disk I/O via 197Bug Commands Dskcfig Disk I/O via 197Bug System CallsDisk I/O Error Codes Default 197Bug Controller and Device ParametersNetwork I/O Support RARP/ARP Protocol Modules Bootp Protocol ModulePhysical Layer Manager Ethernet Driver UDP/IP Protocol ModulesMultiprocessor Control Register Mpcr Method Network Boot Control ModuleNetwork I/O Error Codes Multiprocessor SupportMpar Gcsr Method Diagnostic FacilitiesDebugger General Information Debugger Entering Debugger Command LinesExpression as a Parameter Syntactic VariablesData Type Base Identifier Examples Address Formats Address as a ParameterOffset Registers Port Numbers Entering and Debugging ProgramsHardware Functions Calling System Utilities From User ProgramsPreserving The Debugger Operating Environment 197Bug Vector Table and WorkspaceCPU/MPU Registers Floating Point SupportDouble Precision Real Single Precision RealScientific Notation Debugger Commands 197Bug Debugger Command SetNocm Noma Name Nioc RL Addrbhw Using the 197Bug Debugger Cnfg MI Configure Board Information BlockENV D Set Environment to Bug/Operating SystemENV Parameter and Options Default Meaning of Default Table A-1. ENV Command ParametersConfigure and Environment Commands Ffbffffc Table A-1. ENV Command Parameters Memory Requirement s 01FFFFFF Table A-1. ENV Command Parameters Efffffff FF7FFFFF Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Disk/Tape Controller Modules Supported DISK/TAPE Controller DataMVME323 4 Devices Disk/Tape Controller Default ConfigurationsSingle Board Computers 7 Devices MVME320 4 DevicesMVME328 14 Devices MVME327A 9 DevicesMVME350 1 Device IOT Parameter IOT Command Parameters for Supported Floppy TypesDisk/Tape Controller Data Network Controller Modules Supported Network Controller DataNetwork Controller Data Numerics SymbolsIN-2 IN-3 Nvram A-2 XON/XOFF Index

Related manuals

Manual 78 pages 27.46 Kb