Motorola manual MVME197LE Module Installation

Page 39

	Installation Instructions
	MVME197LE Module Installation	2
	Now that the MVME197LE module is ready for installation, proceed as	2

	follows:

a.Turn all equipment power OFF and disconnect the power cable from the power source.

Caution

!

WARNING

Inserting or removing modules while power is applied could result in damage to module components.

DANGEROUS VOLTAGES, CAPABLE OF CAUSING DEATH, ARE PRESENT IN THIS EQUIPMENT. USE EXTREME CAUTION WHEN HANDLING, TESTING, AND ADJUSTING.

b.Remove the chassis cover as instructed in the equipment user’s manual.

c.Remove the filler panel(s) from the appropriate card slot(s) at the front and rear of the chassis (if the chassis has a rear card cage). The MVME197LE module requires power from both P1 and P2. It may be installed in any double-height unused card slot, if it is not configured as the system controller. If the MVME197LE is configured as the system controller, it must be installed in the left-most card slot (slot 1) to correctly initiate the bus-grant daisy-chain and to have proper operation of the IACK-daisy- chain driver. The MVME197LE is to be installed in the front of the chassis and the MVME712X transition board which has a double-wide front panel is to be installed in the rear of the chassis.

d.Carefully slide the MVME197LE module into the card slot. Be sure the module is seated properly into the P1 and P2 connectors on the backplane. Do not damage or bend connector pins. Fasten the module in the chassis with screws provided, making good contact with the transverse mounting rails to minimize RFI emissions.

e.Remove the IACK and BG jumpers from the header on the chassis backplane for the card slot in which the MVME197LE is installed.

f.Connect the P2 Adapter Board and specified cable(s) to the MVME197LE at P2 on the backplane at the MVME197LE slot, to mate with (optional) terminals or other peripherals at the EIA-232-D serial ports, parallel port, SCSI ports, and LAN Ethernet port. Refer to the manuals listed in Related Documentation section for information on installing the P2 Adapter Board and the MVME712X transition module. (Some connection diagrams are

MVME197LEIG/D1

2-7

Image 39

Contents MVME197LE Restricted Rights Legend Document Terminology PrefaceBIT Document Title Motorola Publication Number Related DocumentationPage Page Safety Summary Safety Depends on YOU Contents Hardware Preparation and Installation Using the 197Bug Debugger Appendix a Configure and Environment Commands List of Figures Xiv List of Tables Xvi Overview IntroductionRequirements Features Specifications Block DiagramMVME197LE Specifications Block Diagram Memory Array Bus Data Bus 256 BusSwitchMC88110 Address Data MUX Address Mezzanine Address BusFunctional Description Front Panel Switches and IndicatorsOnboard Dram Data Bus StructureMC88110 MPU Flash MemorySerial Port Interface Battery Backup RAM and ClockVMEbus Interface InterfacesEthernet Interface Printer InterfaceScsi Termination Scsi InterfacePeripheral Resources Processor Bus Memory Map ConnectorsMemory Maps Interrupt SourcesDramsize Processor Bus Memory MapLocal Devices Memory Map Address Range Devices Accessed Port SizeVMEbus Accesses to the Local Peripheral Bus VMEbus Memory MapVMEbus Short I/O Memory Map Hardware Preparation Unpacking InstructionsHardware Preparation and Installation VMEbus Connector P1 Configuration Switches Switch S1Configuration Switch S1 General Information S1-1 to S1-8 OFF -- All Ones Factory Configuration Switch S6 Installation InstructionsMVME197LE Module Installation System Considerations MVME197LEIG/D1 Hardware Preparation and Installation Description of 197Bug Overview of M88000 FirmwareInstallation and Start-up Comparison With M68000-Based Firmware197Bug Implementation Ote Terminal to make sure XON/XOFF handshaking is enabledAutoboot Network Boot ROMbootRestarting the System ResetBreak AbortMemory Requirements SYSFAIL* Assertion/NegationMPU Clock Speed Calculation DEL Terminal Input/Output ControlDisk I/O Support Blocks Versus SectorsDevice Probe Function Disk I/O via 197Bug Commands Dskcfig Disk I/O via 197Bug System CallsDefault 197Bug Controller and Device Parameters Disk I/O Error CodesNetwork I/O Support RARP/ARP Protocol Modules Bootp Protocol ModulePhysical Layer Manager Ethernet Driver UDP/IP Protocol ModulesMultiprocessor Control Register Mpcr Method Network Boot Control ModuleNetwork I/O Error Codes Multiprocessor SupportMpar Gcsr Method Diagnostic FacilitiesDebugger General Information Debugger Entering Debugger Command LinesExpression as a Parameter Syntactic VariablesData Type Base Identifier Examples Address as a Parameter Address FormatsOffset Registers Port Numbers Entering and Debugging ProgramsHardware Functions Calling System Utilities From User ProgramsPreserving The Debugger Operating Environment 197Bug Vector Table and WorkspaceCPU/MPU Registers Floating Point SupportSingle Precision Real Double Precision RealScientific Notation Debugger Commands 197Bug Debugger Command SetNocm Noma Name Nioc RL Addrbhw Using the 197Bug Debugger Cnfg MI Configure Board Information BlockENV D Set Environment to Bug/Operating SystemENV Parameter and Options Default Meaning of Default Table A-1. ENV Command ParametersConfigure and Environment Commands Ffbffffc Table A-1. ENV Command Parameters Memory Requirement s 01FFFFFF Table A-1. ENV Command Parameters Efffffff FF7FFFFF Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Disk/Tape Controller Modules Supported DISK/TAPE Controller DataMVME323 4 Devices Disk/Tape Controller Default ConfigurationsSingle Board Computers 7 Devices MVME320 4 DevicesMVME328 14 Devices MVME327A 9 DevicesMVME350 1 Device IOT Parameter IOT Command Parameters for Supported Floppy TypesDisk/Tape Controller Data Network Controller Modules Supported Network Controller DataNetwork Controller Data Numerics SymbolsIN-2 IN-3 Nvram A-2 XON/XOFF Index

Related manuals

Manual 78 pages 27.46 Kb