Billion Electric Company 7100SV manual Rear Ports, Cabling

Page 10

Billion BIPAC 7100SV VoIP ADSL Router

2.3 The Rear Ports

 

 

LED

 

 

Meaning

 

 

 

 

 

 

 

 

 

 

Power Switch

 

 

A Power ON/OFF switch

 

 

 

 

 

 

 

 

 

 

Power Jack

 

 

Connect the supplied power adapter to this jack.

 

 

 

 

 

 

 

 

 

 

Reset

 

 

Press it to restore the factory default setting back.

 

 

 

 

 

 

 

 

 

 

VoIP

 

 

Connect RJ-11 cable to this port when connecting to an analog phone

 

 

 

 

 

set.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect the supplied Ethernet cable to this port when connecting to a

 

 

 

LAN

 

 

NIC (Network Interface card) in PC.

 

 

 

(RJ-45

 

 

Connect an UTP Ethernet cable to this port when connecting to a LAN

 

 

 

connector)

 

 

 

 

 

 

 

 

such as an office or home network.

 

 

 

 

 

 

 

 

 

 

LINE

 

 

Connect the supplied RJ-11 cable to this port when connecting to the

 

 

 

(RJ-11

 

 

 

 

 

 

 

ADSL

 

 

 

connector)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.4 Cabling

The most common problem associated with Ethernet is bad cabling or ADSL line. Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. As a first check, please verify that the PWR, LAN and ADSL LEDs are lit and SYS LED is blinking. If they are not, verify that you are using the proper cables.

So long as the cables are connected and the LEDs are lit normally, follow “Chapter 3 Configuration” below to modify the network settings.

6

Image 10
Contents Bipac 7100SV Page Chapter Appendix Chapter Introduction An Overview of Bipac 7100SVPackage Contents Bipac 7100SV FeaturesIntroduction Bipac 7100SV Application Front LEDs Lit green when power adapter is connectedLit green when the LAN link is connected MeaningRear Ports CablingBefore Configuration Configuring PC in Windows XPBillion Bipac 7100SV VoIP Adsl Router Configuring PC in Windows ConfigurationBillion Bipac 7100SV VoIP Adsl Router Configuring PC in Windows 95/98/ME Then select the DNS Configuration Configuring PC in Windows NT4.0 Factory Default Settings Dhcp server function Information from ISPLAN Port WAN Port IP address IP addresses forConfiguring with Web Browser Status Quick StartStatus Adsl Status Adsl Status WAN Status Adsl Status ATM Status Status LAN Status Status- PPP Status LAN Status TCP StatusStatus- Learned MAC Table Routing TableSystem Log Security Logs Adsl Quick StartVoIP Quick Start 3.1 WAN Select AdapterConfiguration Static IP Settings Service Category Select UBR or CBR Dhcp ClientMAC Spoofing 3.2 LAN Device IP AddressVoIP Configuration AuthorizationUserID Same as UserIDService Provider Phone Book Dial Plan Call Feature CallForwarding 3.3.6 PTM Ring Tone Configuration Timer Password SystemTime Zone Upgrade Factory Setting RestartFirewall Packet FilteringBillion Bipac 7100SV VoIP Adsl Router Bridge Filtering Intrusion Detection Block WAN Request Virtual Server Advanced Adsl3.7.2 DNS Dynamic DNS 3.7.4 NAT Configuration 3.7.5 RIP Static Route Misc Configuration Testing Ethernet LAN connection Diagnostic TestPPP Half Bridge Default at Disabled Testing Adsl SynchronizationTest Ethernet connect to ATM Test ATM OAM Segment Loop BackTest ATM OAM End-to-End Loop Back Test IP connect to PPPConfiguration Save Config Problems with the LAN Interface Corrective Action Problems Starting Up the Adsl Router Corrective ActionProblems with the WAN Interface Corrective Action Problems Connecting to a Remote Node or ISPAppendix Contact Billion