Iomega 03798300 Watch the instructional video, Write down the serial number of your Zip

Page 5

3

Watch the instructional video.

Before installing the hardware for your Zip® Internal drive, insert the

Owner’s Manual CD and click the button that says “Watch Installation Video” to give you an overview of the installation process.

4

Write down the serial number of your Zip®

Internal ATAPI drive for future reference.

You will need the serial number of your Zip Internal drive for registration

 

 

purposes or if you need to call technical support. The serial number is

 

located on the label on the top of your Zip drive. Write it down and keep

 

it with your documentation.

5

DISCONNECT the computer power cord and

remove the cover. (Refer to your computer manual

for more complete instructions.)

 

 

Some computers require removing the computer’s face plate as well as the

 

cover to access the drive bays.

 

 

 

WARNING

Always disconnect computer electrical power before

 

beginning a

computer hardware change. M

MIMPORTANT! Be aware that computers are arranged differently and that your computer may not look like the illustrations shown. M

Installation Guide

5

Image 5
Contents Internal Atapi Drive Table of Contents Welcome to Zip Drive Unpack the Zip Internal Atapi drive Check system requirementsWatch the instructional video Disconnect the computer power cordWrite down the serial number of your Zip Internal Atapi drive for future referenceIdentifying the computer’s IDE configuration Locate the IDE channels using the CD drive Identify your computer’s IDE configuration1b Locate the IDE channels using the computer’s hard drive Follow these instructions if you were unable to1c Possible IDE channel locations If the hard drive is the only IDE device connected Determining your computer’s configurationInstallation Guide Panel cover Check the jumper setting on the Zip driveGuide Currently connected to your CD drive Slide the Zip drive into the drive bayRemove the IDE Interface cable that is Verify that the jumper on your CD drive is set to Master Secure drive in drive bay Connect an internal computer power supplyCable to the Zip drive Guide Locate a vacant 31/2 or 51/4 drive bay Change the jumper setting to Master2a3 1/2 drive bays only May require side railsWith the Zip drive. Find the colored stripe or Locate the data cable that comes packagedPrint on one side of the data cable showing PINZip drive Internal drive. M Cable to your Zip driveGuide CD drive If the Iomega software setup program doesNot start automatically, follow these steps SoftwareWindows 95/98 Users Additional instructions for your systemDownload Software from the Iomega Web Site How to Install Without a CD DriveCreate Install Floppy Diskettes Installation Guide Inserting Zip Disks Operating Your Zip DriveDrive Sleep Disk Eject in Case of Power LossEjecting Zip Disks Compatibility with 100MB Zip Disks Zip Tips RecordIt Software Step Backup/RestoreCopy Machine Iomega ToolsDrive Shortcuts For information on how to use IomegaWare softwareCopying Zip Disks Backing Up with Zip DisksFormatting Zip Disks under Windows 95/98 or NT Installing Applications to Zip DisksFormatting Zip Disks Read/Write Protecting Zip Disks Setting Zip Disk Protection under Windows 95/98 and NTWhat is ATAPI? What is IDE?Jumper Settings How IDE WorksBIOS/CMOS Support Possible System IDE/ATAPI ConfigurationsSlave Drive Master DriveGreen activity light on the Zip drive does not turn on TroubleshootingTroubleshooting Installing the Zip drive changes other drive letters Data transfer problems or drive operation is erraticWindows 95/98 Users Troubleshooting You want to use Windows 95/98 DOS mode with your Zip drive Automated Voice Technical Support How to Get HelpOne-on-One Iomega Technical Support Automated FAX-back Help 801 778-5763 U.S. & CanadaReturn or Repair Limited Warranty InformationProduct Information International Support NumbersModel Number Z250ATAPI FCC United States Regulatory InformationCanadian Verification CE European CommunityVisit our web site