Multitech MT5600BLV.90, MT5600BAV.92 manual Appendix a Regulatory Compliance, FCC Part 68 Telecom

Page 47

Appendix A - Regulatory Compliance

Appendix A: Regulatory Compliance

FCC Part 68 Telecom

1.This equipment complies with part 68 of the Federal Communications Commission Rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number. This information must be provided to the telephone company.

2.The suitable USOC jack (Universal Service Order Code connecting arrangement) for this equipment is shown below. If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.

3.An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant. See installation instructions for details.

4.The ringer equivalence number (REN) is used to determine the number of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the device not ringing in response to an incoming call. In most, but not all, areas the sum of the RENs should not exceed 5.0. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the local telephone company.

5.If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

6.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service.

7.If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.

8.No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void registration and warranty.

9.This equipment should not be used on party lines or coin lines.

10.If so required, this equipment is hearing-aid compatible.

11.Manufacturing Information:

Manufacturer:

Multi-Tech Systems, Inc.

Trade Name

MultiModemII

Model Number:

MT5600BA

FCC Registration No:

AU7USA-33378-M5-E

Ringer Equivalence No:

0.1A

Modular Jack (USOC):

RJ11C or RJ11W (single line)

Service Center in USA:

Multi-Tech Systems, Inc.

 

2205 Woodale Drive

 

Mounds View, MN 55112

 

U.S.A.

 

(763) 785-3500

 

(763) 785-9874 Fax

MT5600BA/BL Series User Guide

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents MT5600BA-V.92 MT5600BA-V.90 MT5600BL-V.90 MT5600BA/BL SeriesRevision Date Description Table of Contents Contents Product Description Description and FeaturesFeatures Safety Warnings Connect the Modem to Your System InstallationConnect the Phone to the Modem Optional Removing an Old Modem Driver Install the Modem DriverMT5600BA-V.92 Only Country Code ConfigurationInstall Phone Tools LED Indicators Using the Front PanelModem Configuration Menu Structure Liquid Crystal Display LCDOption Selection Twigs Menu OverviewStatus Trunk Basic Options Trunk From previous Advanced Options Trunk Advanced Options Trunk Diagnostic Options Trunk Remote Configuration Options TrunkCaller ID Options Trunk Phone Number Memory Options TrunkStatus Menu OptionsBasic Options Using the Front Panel Advanced Options Using the Front Panel Phone Number Memory Options Remote Configuration OptionsDiagnostic Options Caller ID Options Leased-Line Operation Two-Wire SetupFour-Wire Setup Dial Backup and Leased Line Restoral Setup Dial Backup and Leased-Line RestoralLeased Line Operation Remote Configuration Changing the Remote Escape Character Callback Security Setup ProceduresFront Panel Method Assigning Callback PasswordsAssigning Callback Phone Numbers Calling Procedure Callback Enable/Disable Callback Security CommandsCallback Assignments Form None of the Indicators Light TroubleshootingModem Does Not Respond to Commands Modem Cannot Connect When Dialing Modem Disconnects While Online Data Is Being Lost Modem Cannot Connect When AnsweringFile Transfer Is Slower Than It Should Be Fax and Data Software Can’t Run at the Same Time There Are Garbage Characters on the MonitorModem Doesn’t Work with Caller ID FCC Part 68 Telecom Appendix a Regulatory ComplianceCanadian Limitations Notice Fax Branding StatementNew Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions South African Notice Modem Compatibility Appendix B Technical SpecificationsTransmission Level Multi-Tech Systems, Inc. Warranty & Repairs Policies Appendix C Warranty, Service, Technical SupportRepair Procedures for International Distributors Online Warranty Registration ServiceInternational Customers outside U.S.A. and Canada Replacement PartsInternet Sites Technical SupportIdentify the Modem Firmware Upgrade OverviewAppendix D Upgrading the Firmware IntroductionIdentify the Current Firmware Version Download the Upgrade FileExtract the Upgrade Files Clear Your Stored Paramenters Upgrade the Modem’s FirmwareRestore Your Parameters Appendix E Installing a Modem Under Linux Using the Modem to Call the Internet RS-232 Pin Descriptions Appendix F Pin DescriptionsRDL RS-232 Cable PinoutsFig. F-3. Macintosh cable Leased Line PinoutsIndex Index
Top Page Image Contents