Multitech MT5600BLV.90, MT5600BAV.92, MT5600BAV.90 manual Connect the Phone to the Modem Optional

Page 8

Chapter 2 - Installation

Connect the Four-Wire Leased Line

MT5600BL Only – Plug one end of a four-wire phone cable into the modem's LEASED jack; connect the other end to a four-wire leased line wall jack or terminals.

Modems with a leased-line jack support the dial backup feature. For dial backup operation, plug one end of your dialup modular phone cable into the modem’s LINE jack and the other end into a PSTN wall jack.Plug one end of a two-wire or four-wire phone cable into the modem’s LEASED jack, and connect the other end to a leased-line wall jack or terminals.

Modems with a leased-line jack support the dial backup feature. For dial backup operation, plug one end of your dialup modular phone cable into the modem’s LINE jack and the other end into a PSTN wall jack.

Connect the Phone to the Modem (Optional)

For voice-only calls, plug a telephone into the modem’s PHONE jack.

Connect the Modem to the AC Power Outlet

Plug the power transformer into an AC power outlet or power strip. Plug the power transformer’s cable into the POWER jack on the modem.

Note: Use only the power transformer supplied with the modem. Use of any other transformer voids the warranty and can damage the modem.

Power-On Test

Test the modem by turning it on (a power switch is located on the front panel). When you apply power, the modem performs a diagnostic self-test, indicated by the TM indicator lighting for a few seconds, after which the LCD should light. If this does not happen, check that the power switch is on, the power transformer is solidly connected, and the AC outlet is live. If these measures do not work, see the “Troubleshooting” chapter.

MT5600BA/BL Series User Guide

8

Image 8

Contents MT5600BA/BL Series MT5600BA-V.92 MT5600BA-V.90 MT5600BL-V.90Revision Date Description Table of Contents Contents Product Description Description and FeaturesFeatures Safety Warnings Installation Connect the Modem to Your SystemConnect the Phone to the Modem Optional Install the Modem Driver Removing an Old Modem DriverCountry Code Configuration MT5600BA-V.92 OnlyInstall Phone Tools LED Indicators Using the Front PanelModem Configuration Menu Structure Liquid Crystal Display LCDOption Selection Menu Overview TwigsStatus Trunk Basic Options Trunk From previous Advanced Options Trunk Advanced Options Trunk Remote Configuration Options Trunk Diagnostic Options TrunkPhone Number Memory Options Trunk Caller ID Options TrunkMenu Options StatusBasic Options Using the Front Panel Advanced Options Using the Front Panel Phone Number Memory Options Remote Configuration OptionsDiagnostic Options Caller ID Options Two-Wire Setup Leased-Line OperationFour-Wire Setup Dial Backup and Leased-Line Restoral Dial Backup and Leased Line Restoral SetupLeased Line Operation Remote Configuration Changing the Remote Escape Character Setup Procedures Callback SecurityAssigning Callback Passwords Front Panel MethodAssigning Callback Phone Numbers Calling Procedure Callback Security Commands Callback Enable/DisableCallback Assignments Form Troubleshooting None of the Indicators LightModem Does Not Respond to Commands Modem Cannot Connect When Dialing Modem Disconnects While Online Data Is Being Lost Modem Cannot Connect When AnsweringFile Transfer Is Slower Than It Should Be Fax and Data Software Can’t Run at the Same Time There Are Garbage Characters on the MonitorModem Doesn’t Work with Caller ID Appendix a Regulatory Compliance FCC Part 68 TelecomFax Branding Statement Canadian Limitations NoticeNew Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions South African Notice Appendix B Technical Specifications Modem CompatibilityTransmission Level Appendix C Warranty, Service, Technical Support Multi-Tech Systems, Inc. Warranty & Repairs PoliciesOnline Warranty Registration Service Repair Procedures for International DistributorsReplacement Parts International Customers outside U.S.A. and CanadaTechnical Support Internet SitesUpgrade Overview Appendix D Upgrading the FirmwareIntroduction Identify the Modem FirmwareIdentify the Current Firmware Version Download the Upgrade FileExtract the Upgrade Files Clear Your Stored Paramenters Upgrade the Modem’s FirmwareRestore Your Parameters Appendix E Installing a Modem Under Linux Using the Modem to Call the Internet Appendix F Pin Descriptions RS-232 Pin DescriptionsRS-232 Cable Pinouts RDLLeased Line Pinouts Fig. F-3. Macintosh cableIndex Index