Multitech MT5600BLV.90, MT5600BAV.92, MT5600BAV.90 manual South African Notice

Page 50

Appendix A - Regulatory Compliance

4.This device is equipped with pulse dialing, while the Telecom standard is DTMF tone dialing. There is no guarantee that Telecom lines will always continue to support pulse dialing.

Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to ‘bell tinkle’ or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service.

The preferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic) dialing and is readily available on almost all New Zealand telephone exchanges.

5.Warning Notice: No ‘111’ or other calls can be made from this device during a mains power failure.

6.This equipment may not provide for the effective hand-over of a call to another device connected to the same line.

7.Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom’s Specifications:

For repeat calls to the same number:

·There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation, and

·The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt.

For automatic calls to different numbers:

·The equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is no less than 5 seconds between the end of one call attempt and the beginning of an- other.

For automatically answered incoming calls:

·The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of re- ceipt of ringing.

8.For correct operation, total of the RNs of all devices connected to a single line at any time should not exceed 5.

South African Notice

This modem must be used in conjunction with an approved surge protection device.

MT5600BA/BL Series User Guide

50

Image 50

Contents MT5600BA/BL Series MT5600BA-V.92 MT5600BA-V.90 MT5600BL-V.90Revision Date Description Table of Contents Contents Product Description Description and FeaturesFeatures Safety Warnings Installation Connect the Modem to Your SystemConnect the Phone to the Modem Optional Install the Modem Driver Removing an Old Modem DriverCountry Code Configuration MT5600BA-V.92 OnlyInstall Phone Tools LED Indicators Using the Front PanelModem Configuration Menu Structure Liquid Crystal Display LCDOption Selection Menu Overview TwigsStatus Trunk Basic Options Trunk From previous Advanced Options Trunk Advanced Options Trunk Remote Configuration Options Trunk Diagnostic Options TrunkPhone Number Memory Options Trunk Caller ID Options TrunkMenu Options StatusBasic Options Using the Front Panel Advanced Options Using the Front Panel Phone Number Memory Options Remote Configuration OptionsDiagnostic Options Caller ID Options Two-Wire Setup Leased-Line OperationFour-Wire Setup Dial Backup and Leased-Line Restoral Dial Backup and Leased Line Restoral SetupLeased Line Operation Remote Configuration Changing the Remote Escape Character Setup Procedures Callback SecurityAssigning Callback Passwords Front Panel MethodAssigning Callback Phone Numbers Calling Procedure Callback Security Commands Callback Enable/DisableCallback Assignments Form Troubleshooting None of the Indicators LightModem Does Not Respond to Commands Modem Cannot Connect When Dialing Modem Disconnects While Online Data Is Being Lost Modem Cannot Connect When AnsweringFile Transfer Is Slower Than It Should Be Fax and Data Software Can’t Run at the Same Time There Are Garbage Characters on the MonitorModem Doesn’t Work with Caller ID Appendix a Regulatory Compliance FCC Part 68 TelecomFax Branding Statement Canadian Limitations NoticeNew Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions South African Notice Appendix B Technical Specifications Modem CompatibilityTransmission Level Appendix C Warranty, Service, Technical Support Multi-Tech Systems, Inc. Warranty & Repairs PoliciesOnline Warranty Registration Service Repair Procedures for International DistributorsReplacement Parts International Customers outside U.S.A. and CanadaTechnical Support Internet SitesIntroduction Upgrade OverviewAppendix D Upgrading the Firmware Identify the Modem FirmwareIdentify the Current Firmware Version Download the Upgrade FileExtract the Upgrade Files Clear Your Stored Paramenters Upgrade the Modem’s FirmwareRestore Your Parameters Appendix E Installing a Modem Under Linux Using the Modem to Call the Internet Appendix F Pin Descriptions RS-232 Pin DescriptionsRS-232 Cable Pinouts RDLLeased Line Pinouts Fig. F-3. Macintosh cableIndex Index