Technics DP-1810P manual Platen, Manual Skyshot Mode

Page 23

Other Features

Manual Skyshot Mode

When using this function, the custom size should be registered into memory (M1, M2) in advance. (See page 29)

Platen

Upper- left corner

 

 

 

1

2

3

4

Place the

Select the Custom

Number of

Press

Original

Size (M1/F3 or M2/F4)

Copies

START

Making Copies

2

FUNCTION MODE (1-2) ENTER NO. OR ∨ ∧

2:COPIER SETTINGS PRESS SET TO SELECT

COPIER PARAM. (00-14) ENTER NO. OR ∨ ∧

07 MANUAL SKYSHOT 2:M1 ON

#Press the 2 key to select COPIER SETTINGS.

$Press the SET key.

%Press 7 and SET key to select MANUAL SKYSHOT.

&Press 2 or 3 key to select the Custom Size.

1: OFF

NONE

2: M1 ON

M1 size is ON*

3: M2 ON

M2 size is ON*

4: M1, M2 ON

Both sizes are ON

(Press the SET key. )Press the Reset key.

NOTE

The default size for M1 is: 70(X) 160(Y) mm, and M2 is: 95(X) 220(Y) mm

CWhen changing the M1 or M2 size, consult with the key operator.

 

 

CWhen using the manual skyshot mode, M1 and M2 are turned ON and other

 

job memory cannot be used.

 

CPress the RESET key to cancel all job settings.

23

Image 23
Contents English Others Before StartingOptions Model and Serial Number Important InformationCommon Features and Usage Operation ChartEnergy Star Table of Contents Others Problem SolvingOptions Manufacturer’s name and address Factory ID PrecautionsFor Your Safety Laser SafetyToner and Paper Ventilation HandlingFCC Warning For U.S.A InstallationControl Panel Interrupt Key, Memory In Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Start Key$Select exposure control Basic CopyFull Size Copying Copying the Same Size OriginalsSize Copying with Preset RatiosReset Reduction or Enlargement CopyingZoom Zoom CopyingSheet Bypass Side Guides Using the Sheet Bypass$Adjust the side guides Copying on Special Paper, etc1 key Creative FeaturesProcedure 1 CopyCopy CopyMargin Book/Edge/MarginBook Edge$Press the Memory In F2 key Job MemoryTo store a job in memory To recall a job stored in memoryFrom Platen Glass only Sort CopySort Copy Sleep Mode Other FeaturesEnergy Saver/Interrupt Mode Energy Saver ModeNormal Skyshot ModeDigital Skyshot Mode NonePlaten Manual Skyshot ModeCopy Combined Function TableOriginal SortInput Identification Code Using Function Modes to Change the Initial Copy ModesFunction OptionsGeneral Functions Modes Function Initial SettingModes Function Copier SettingsGeneral Functions for Key Operator Copier Settings for Key Operator Press the Function Key Proceed as Follows Function SettingChanging the Auto Exposure Setting B5R Function Setting for Key OperatorChanging the Paper Size Stopper Guide a Paper Guide b PaperFunctions Departmental CounterSelect the Department Counter Mode Components Accessories$2 in 1 Copy Automatic Document FeederADF DA-AS180 # Automatic Original FeedingInappropriate originals Place OriginalSheet Paper Tray Problem SolvingAdding Paper J Cap Adding the Toner and Replacing Toner Waste Container ?Problem Solving Paper Misfeed Locations Removing a Misfed PaperPaper Exit Area Surface Paper Entry/Transport AreaHot HeatedPaper Feed Module ADF Unit Does Not Operate TroubleshootingBefore Calling Service Check ActionMarked Copies Light CopiesGlass User Error Codes U CodeCode Display Message Check Points CoverDP-1810P Copier Specifications2nd Paper Feed Module DA-DS182 SpecificationsPart Name Remarks Options and SuppliesFor Printer SuppliesPage Page Warranty