Technics DP-1810P manual Function Setting for Key Operator, Changing the Paper Size, B5R

Page 31

Function

Function Setting for Key Operator

■Changing the Paper Size

The paper trays are designed to accommodate invoice, letter, letter R, legal and ledger size paper. To change the paper size, perform the steps shown below.

1	Press the Function Key
	Press the Function Key
	�

2	Proceed as Follows:

			FUNCTION MODE	(1-2)
			ENTER NO. OR ∨	∧

#Press the 1 key to select GENERAL FUNCTIONS.

1:GENERAL FUNCTIONS PRESS SET TO SELECT

$Press the SET key.

GENERAL PARAM. (0-9)

ENTER NO. OR ∨ ∧

%Press 9 key.

09 KEY OPERATOR MODE ENTER PASSWORD=- ■ ■

&Input the Key Operator ID code (3 digit) and the SET key.

KEY OPR. MODE (00-25)

ENTER NO. OR ∨ ∧

(Press 00 and 1 or 2 key to select the PAPER SIZE.

00 PAPER SIZE 1:TRAY-1[LTRB]

)Press SET to select the paper tray and press (G or F) keys to set the paper size.

Paper size changes are as follows.

Letter R Invoice R A3 B4 A4

Letter									A4R

Legal									B5
	Ledger		FLS2		FLS1		A5R		B5R

*Press the SET key to set up the PAPER SIZE.

+Press the RESET key, then exit the Function mode.

Making Copies

31

Image 31

Contents Options Before StartingEnglish Others Model and Serial Number Important InformationCommon Features and Usage Operation ChartEnergy Star Table of Contents Options Problem SolvingOthers Manufacturer’s name and address Factory ID PrecautionsFor Your Safety Laser SafetyToner and Paper Ventilation HandlingFCC Warning For U.S.A InstallationControl Panel Interrupt Key, Memory In Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Start Key$Select exposure control Basic CopyFull Size Copying Copying the Same Size OriginalsSize Copying with Preset RatiosReset Reduction or Enlargement CopyingZoom Zoom CopyingSheet Bypass Side Guides Using the Sheet Bypass$Adjust the side guides Copying on Special Paper, etc1 key Creative FeaturesProcedure 1 CopyCopy CopyMargin Book/Edge/MarginBook Edge$Press the Memory In F2 key Job MemoryTo store a job in memory To recall a job stored in memorySort Copy Sort CopyFrom Platen Glass only Sleep Mode Other FeaturesEnergy Saver/Interrupt Mode Energy Saver ModeNormal Skyshot ModeDigital Skyshot Mode NonePlaten Manual Skyshot ModeCopy Combined Function TableOriginal SortInput Identification Code Using Function Modes to Change the Initial Copy ModesFunction OptionsGeneral Functions Modes Function Initial SettingModes Function Copier SettingsGeneral Functions for Key Operator Copier Settings for Key Operator Changing the Auto Exposure Setting Function SettingPress the Function Key Proceed as Follows Changing the Paper Size Function Setting for Key OperatorB5R Stopper Guide a Paper Guide b PaperFunctions Departmental CounterSelect the Department Counter Mode Components Accessories$2 in 1 Copy Automatic Document FeederADF DA-AS180 # Automatic Original FeedingInappropriate originals Place OriginalAdding Paper J Problem SolvingSheet Paper Tray Cap Adding the Toner and Replacing Toner Waste Container ?Problem Solving Paper Misfeed Locations Removing a Misfed PaperPaper Exit Area Surface Paper Entry/Transport AreaHot HeatedPaper Feed Module ADF Unit Does Not Operate TroubleshootingBefore Calling Service Check ActionMarked Copies Light CopiesGlass User Error Codes U CodeCode Display Message Check Points CoverDP-1810P Copier Specifications2nd Paper Feed Module DA-DS182 SpecificationsPart Name Remarks Options and SuppliesFor Printer SuppliesPage Page Warranty