Technics DP-1810P manual Adding the Toner and Replacing Toner Waste Container ?, Cap

Page 39

Problem Solving/U13

Adding the Toner and Replacing Toner Waste Container (?)

1	Open the front cover.
	Open the front cover.
2	Remove the toner waste container by
	Remove the toner waste container by
	slowly pulling it towards the left as
	illustrated.

3

Cap

Seal the container with the enclosed cap and dispose of it properly.

4	1
	1
	2

#Turn the empty Toner Bottle

counter-clockwise until it stops. The Arrow mark (Unlocked symbol ) visible on the end of the Toner Bottle is aligned with the Arrow

mark on the machine.

Note: To prevent toner spill, ensure that the key is facing upwards before removing the toner bottle.

$Pull out the empty Toner Bottle. Note: If the bottle will not pull out from

the machine, turn the bottle slightly in either direction to release the key and try it again.

J

?

ATTENTION	CFor optimum copy quality use the recommended Panasonic toner. Store toner in a cool
	dark place. Do not unseal toner before use. Use it as fast as possible after unsealing.

CWhen U13 is displayed the Add Toner Warning Indicator will begin to flash.This message is to prompt you that the toner bottle is nearly empty (approx. 300-sheets can be printed). This message will continue to be displayed until the bottle is replaced. When the count- down counter reaches 0, the copier will stop operating. To clear the message and enable the copier to operate, replace the empty toner bottle with a new one.

39

Image 39

Contents Before Starting OptionsEnglish Others Model and Serial Number Important InformationCommon Features and Usage Operation ChartEnergy Star Table of Contents Problem Solving OptionsOthers Manufacturer’s name and address Factory ID PrecautionsFor Your Safety Laser SafetyToner and Paper Ventilation HandlingFCC Warning For U.S.A InstallationControl Panel Interrupt Key, Memory In Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Start Key$Select exposure control Basic CopyFull Size Copying Copying the Same Size OriginalsSize Copying with Preset RatiosReset Reduction or Enlargement CopyingZoom Zoom CopyingSheet Bypass Side Guides Using the Sheet Bypass$Adjust the side guides Copying on Special Paper, etc1 key Creative FeaturesProcedure 1 CopyCopy CopyMargin Book/Edge/MarginBook Edge$Press the Memory In F2 key Job MemoryTo store a job in memory To recall a job stored in memorySort Copy Sort CopyFrom Platen Glass only Sleep Mode Other FeaturesEnergy Saver/Interrupt Mode Energy Saver ModeNormal Skyshot ModeDigital Skyshot Mode NonePlaten Manual Skyshot ModeCopy Combined Function TableOriginal SortInput Identification Code Using Function Modes to Change the Initial Copy ModesFunction OptionsGeneral Functions Modes Function Initial SettingModes Function Copier SettingsGeneral Functions for Key Operator Copier Settings for Key Operator Function Setting Changing the Auto Exposure SettingPress the Function Key Proceed as Follows Function Setting for Key Operator Changing the Paper SizeB5R Stopper Guide a Paper Guide b PaperFunctions Departmental CounterSelect the Department Counter Mode Components Accessories$2 in 1 Copy Automatic Document FeederADF DA-AS180 # Automatic Original FeedingInappropriate originals Place OriginalProblem Solving Adding Paper JSheet Paper Tray Cap Adding the Toner and Replacing Toner Waste Container ?Problem Solving Paper Misfeed Locations Removing a Misfed PaperPaper Exit Area Surface Paper Entry/Transport AreaHot HeatedPaper Feed Module ADF Unit Does Not Operate TroubleshootingBefore Calling Service Check ActionMarked Copies Light CopiesGlass User Error Codes U CodeCode Display Message Check Points CoverDP-1810P Copier Specifications2nd Paper Feed Module DA-DS182 SpecificationsPart Name Remarks Options and SuppliesFor Printer SuppliesPage Page Warranty