3Com manual Software, Compatibility, SW/2500, can be used only with the CS/2500 and CS/2600

Page 18

1-2 CHAPTER 1: OVERVIEW

2 MB of memory

Ethernet attachment unit interface (AUI)

Support for parallel printers with Centronics™ interf aces

 

Model CS/2500 has no diskette drive. This configuration is

 

advantageous in environments where disk contamination is possible or

 

where users are not allowed access to system software. The CS/2500

 

boots over the network from a 3Com Remote Boot and Configuration

 

Services (RBCS) server or a generic Trivial File Transfer Protocol/File

 

Transfer Protocol (TFTP/FTP) server.

 

Although some multiprotocol communications software packages

 

include Network Control Server (NCS) software for backward

 

compatibility, 3Com no longer provides technical support for NCS

 

software or servers.

 

 

 

Model CS/2600 has a 3.5-inch internal diskette drive. This model can

 

boot either over the network or locally from the internal diskette drive.

 

 

Software

Models CS/2500 and CS/2600 communications servers use different

Compatibility

software versions from the earlier models CS/2000 and CS/2100. The

 

software versions listed in Table 1-1, and other software with the prefix

 

SW/2500, can be used only with the CS/2500 and CS/2600.

 

Table 1-1 Software Compatible with CS/2500 and CS/2600

 

 

 

 

 

Software

Label and Version

 

 

 

 

 

TCP/OSI

SW/2500-TO-3270, 5.0 or later

 

TCP/LAT/OSI

SW/2500-TLO-3270, 5.0 or

 

 

later

 

 

 

 

In mixed environments, you can configure a CS/2500 or CS/2600 to emulate a CS/2000 or CS/2100 and therefore to be compatible with CS/2000 and CS/2100 software. For information on configuring this emulation, refer to “Emulating a CS/2000 or CS/2100” on page 4-12.

Image 18
Contents CS/2500 Series 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Installation Maintenance and Upgrades PIN Assignments Technical Support Page Figures Tables Audience About this GuideIntroduction ConventionsThis Typeface Italics Italics are used to denote new terms or emphasis About this Guide Overview FeaturesFeatures Ten standard RS-232-D electrical interfacesSoftware CompatibilitySW/2500, can be used only with the CS/2500 and CS/2600 Chassis Panel, see Back Panel onHardware Interrupt Front Panel Its +5 V DC output Power supply module and three types of connectors Back PanelCS/2500 and CS/2600 back panel, shown in -5, contains Overview Back Panel Overview Specifications Optional RackMount Kit VAC Installation Do the following before beginning the installationPreparation Installation Install brackets Cabling the Server To the NetworkTurning on the server All ports are set to terminal SETDefault -TERM DeVice = Installation Slide-lock connection on the server End to the transceiverInstall brackets Configuration, and Appendix C, Monitor Utility ConfigurationAC power source must meet the requirements outlined ModifyingInstallation Startup Guide or software release notes Rbcs files Booting fromDiskette DisketteStartup 3Com Corporation CS/2000 Series Monitor Reading...OK Insert copy and hit return to continue Parameter changes Messages Boot ProblemsNormal Startup Shutting DownShutting Down Startup Configuration EnteringFirmware Monitor Configuration Procedure ChangingFollowing menu is displayed SLP Changing the Configuration Configuration Changing the Configuration SLP, and Trivial File Transfer Protocol Tftp Used with 3Com Network Control Servers NCSs Com no longerNext section Type B Change IP/TFTP Parameters menu appears TftpConfiguration Bootp Emulating a CS/2000 or CS/2100Software and to operate in mixed environments Changing Port Configuration Changing Port Configuration Configuration 3Com recommends the following procedures for preventive Maintenance and UpgradesMaintenance MaintenanceMaintenance and Upgrades Maintenance Reinstall the fuseholder cartridge in the receptacle Upgrades Upgrade procedures require you to remove the server coverRemoving the Server Cover Grasp both sides of the cover and carefully lift it off Rear8-F Pull taut to expose screw Voltages. There are no user-serviceable parts inside Upgrades Remove Connector from Each pin must be inserted properly into its socket EPROM. Each pin must be inserted properly into its socket Replace the cover, as described in the next sectionUpgrades Maintenance and Upgrades Troubleshooting Troubleshooting Operating Problems Troubleshooting Procedures Memory DumpEnter the density of the dump diskettes Return to use the default density 2mb Troubleshooting Figure A-1 Serial Connector Pin Numbering PIN AssignmentsTXD DTE Transceiver DO-S Slct Startup Messages Appendix B Startup Messages You can access the monitor in either of the following ways Monitor UtilitySet the Auto-reboot parameter to Boot monitor Continuous Self-Test and Initial Boot Source parametersNonfunctional Become nonfunctional, enter the following command Memory dumps, refer to Memory Dump Procedures on-2 on page 1-4. The switch is recessed into a round hole to Dump Procedures onSyntax BT Filename and address parameters specify the name Procedures onUsing this menu, refer to , Configuration From memory locationDescription Repeats the previous command Technical Support Services3Com Bulletin Board Service 3ComBBS On-line TechnicalPress Return to see the ThreeComForum main menu Country Telephone Number Hong Kong 852 2537 44 1442 408 727 Appendix D Technical Support Returning Products For RepairSender’s expense To obtain an RMA number, call or fax 10/25/95 Index NumericsCover Index Index Index Index Limited Warranty Bayfront Plaza Santa Clara, CA 408 764-5000 1/1/94