3Com CS/2500 manual Booting from, Diskette, Rbcs files

Page 41

Booting from Diskette

3-3

 

on the server again. If the problem persists, refer to “Startup Problems”

 

on page 6-1.

 

The Self Test LED remains on during self-test diagnostics, about 40

 

seconds. The server then enters the boot phase. The Boot State LED

 

remains on during boot, and the Packet Received LED lights as the

 

image is received from the RBCS server. This process takes several

 

minutes. Following boot, the server reads additional information from

 

the RBCS files.

Booting from a

To boot your communications server from a generic TFTP/FTP host,

Generic TFTP/FTP

you must configure the communications server firmware and software.

Host

For firmware configuration, refer to Chapter 4, “Configuration.” For

 

software configuration, refer to the Multiprotocol Communications

 

Server Operation Guide or software release notes. Enter the FTP server

 

address under the FAP server IP address parameter in the Change

 

IP/TFTP Parameters submenu.

Remote Reboot

If you plan to reboot your communications server remotely from an

 

RBCS or TFTP server, you must set the Auto-Reboot parameter to

 

Reboot. For information on configuring this parameter, refer to

 

Chapter 4, “Configuration.”

 

Do not connect or disconnect a console during the boot process.

 

Connecting or disconnecting the console cable puts the communications

 

server into monitor mode and aborts the boot process.

 

 

Booting from

Before you use a Model CS/2600 communications server, make a copy

Diskette

of the software distribution diskette. After you copy the distribution

 

diskette, store it in a safe place and use only the copy as the working

 

diskette.

 

If you are upgrading from earlier software, you may be able to copy

 

configuration information from your old working diskette onto the new

 

one. Refer to the software release notes for instructions.

 

You may want to make a backup copy of your working diskette every

 

time you change the values of the software parameters. If for any reason

Image 41
Contents CS/2500 Series 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Installation Maintenance and Upgrades PIN Assignments Technical Support Page Figures Tables Introduction About this GuideAudience ConventionsThis Typeface Italics Italics are used to denote new terms or emphasis About this Guide Features FeaturesOverview Ten standard RS-232-D electrical interfacesSW/2500, can be used only with the CS/2500 and CS/2600 SoftwareCompatibility Panel, see Back Panel on ChassisHardware Interrupt Front Panel Its +5 V DC output CS/2500 and CS/2600 back panel, shown in -5, contains Power supply module and three types of connectorsBack Panel Overview Back Panel Overview Mount Kit SpecificationsOptional Rack VAC Preparation InstallationDo the following before beginning the installation Installation Install brackets Turning on the server Cabling the ServerTo the Network All ports are set to terminal SETDefault -TERM DeVice = Installation End to the transceiver Slide-lock connection on the serverInstall brackets AC power source must meet the requirements outlined ConfigurationConfiguration, and Appendix C, Monitor Utility ModifyingInstallation Startup Guide or software release notes Diskette Booting fromRbcs files DisketteStartup 3Com Corporation CS/2000 Series Monitor Reading...OK Insert copy and hit return to continue Parameter changes Normal Startup Boot ProblemsMessages Shutting DownShutting Down Startup Firmware Monitor ConfigurationEntering Configuration Following menu is displayed ProcedureChanging SLP Changing the Configuration Configuration Changing the Configuration Next section SLP, and Trivial File Transfer Protocol TftpUsed with 3Com Network Control Servers NCSs Com no longer Tftp Type B Change IP/TFTP Parameters menu appearsConfiguration Bootp Software and to operate in mixed environments Emulating aCS/2000 or CS/2100 Changing Port Configuration Changing Port Configuration Configuration Maintenance Maintenance and Upgrades3Com recommends the following procedures for preventive MaintenanceMaintenance and Upgrades Maintenance Reinstall the fuseholder cartridge in the receptacle Upgrade procedures require you to remove the server cover UpgradesRemoving the Server Cover Rear Grasp both sides of the cover and carefully lift it off8-F Pull taut to expose screw Voltages. There are no user-serviceable parts inside Upgrades Remove Connector from Each pin must be inserted properly into its socket Replace the cover, as described in the next section EPROM. Each pin must be inserted properly into its socketUpgrades Maintenance and Upgrades Troubleshooting Troubleshooting Operating Problems Troubleshooting Memory Dump ProceduresEnter the density of the dump diskettes Return to use the default density 2mb Troubleshooting PIN Assignments Figure A-1 Serial Connector Pin NumberingTXD DTE Transceiver DO-S Slct Startup Messages Appendix B Startup Messages Monitor Utility You can access the monitor in either of the following waysNonfunctional Set the Auto-reboot parameter to Boot monitorContinuous Self-Test and Initial Boot Source parameters -2 on page 1-4. The switch is recessed into a round hole to Memory dumps, refer to Memory Dump Procedures onBecome nonfunctional, enter the following command Dump Procedures onSyntax BT Using this menu, refer to , Configuration Procedures onFilename and address parameters specify the name From memory locationDescription Repeats the previous command 3Com Bulletin Board Service 3ComBBS ServicesTechnical Support On-line TechnicalPress Return to see the ThreeComForum main menu Country Telephone Number Hong Kong 852 2537 44 1442 408 727 Appendix D Technical Support Sender’s expense To obtain an RMA number, call or fax Returning ProductsFor Repair 10/25/95 Numerics IndexCover Index Index Index Index Limited Warranty Bayfront Plaza Santa Clara, CA 408 764-5000 1/1/94