3Com CS/2500 manual Chassis, Panel, see Back Panel on

Page 19

Chassis 1-3

When a CS/2500 or CS/2600 is running in CS/2000 or CS/2100 mode, it can use only the software listed in Table 1-2, or other software with the prefix SW/2000 or SW/200.

Table 1-2 Software Compatible with CS/2000 and CS/2100

Software

Label and Version

 

 

 

TCP

SW/2000-T-4.1 or later

 

SW/200-TCP 3.2 or later

TCP/LAT

SW/2000-TL-4.0 or later

OSI/TCP

SW/2000-OT 1.0 or later

 

 

 

Chassis

Figure 1-2 shows the CS/2500 series enclosure, including hardware

 

features common to both models. For a more detailed view of the back

 

panel, see “Back Panel” on page 1-7.

Image 19
Contents CS/2500 Series 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Installation Maintenance and Upgrades PIN Assignments Technical Support Page Figures Tables Conventions About this GuideIntroduction AudienceThis Typeface Italics Italics are used to denote new terms or emphasis About this Guide Ten standard RS-232-D electrical interfaces FeaturesFeatures OverviewCompatibility SoftwareSW/2500, can be used only with the CS/2500 and CS/2600 Panel, see Back Panel on ChassisHardware Interrupt Front Panel Its +5 V DC output Back Panel Power supply module and three types of connectorsCS/2500 and CS/2600 back panel, shown in -5, contains Overview Back Panel Overview Optional Rack SpecificationsMount Kit VAC Do the following before beginning the installation InstallationPreparation Installation Install brackets To the Network Cabling the ServerTurning on the server All ports are set to terminal SETDefault -TERM DeVice = Installation End to the transceiver Slide-lock connection on the serverInstall brackets Modifying ConfigurationAC power source must meet the requirements outlined Configuration, and Appendix C, Monitor UtilityInstallation Startup Guide or software release notes Diskette Booting fromDiskette Rbcs filesStartup 3Com Corporation CS/2000 Series Monitor Reading...OK Insert copy and hit return to continue Parameter changes Shutting Down Boot ProblemsNormal Startup MessagesShutting Down Startup Entering ConfigurationFirmware Monitor Configuration Changing ProcedureFollowing menu is displayed SLP Changing the Configuration Configuration Changing the Configuration Used with 3Com Network Control Servers NCSs Com no longer SLP, and Trivial File Transfer Protocol TftpNext section Tftp Type B Change IP/TFTP Parameters menu appearsConfiguration Bootp CS/2000 or CS/2100 Emulating aSoftware and to operate in mixed environments Changing Port Configuration Changing Port Configuration Configuration Maintenance Maintenance and UpgradesMaintenance 3Com recommends the following procedures for preventiveMaintenance and Upgrades Maintenance Reinstall the fuseholder cartridge in the receptacle Upgrade procedures require you to remove the server cover UpgradesRemoving the Server Cover Rear Grasp both sides of the cover and carefully lift it off8-F Pull taut to expose screw Voltages. There are no user-serviceable parts inside Upgrades Remove Connector from Each pin must be inserted properly into its socket Replace the cover, as described in the next section EPROM. Each pin must be inserted properly into its socketUpgrades Maintenance and Upgrades Troubleshooting Troubleshooting Operating Problems Troubleshooting Memory Dump ProceduresEnter the density of the dump diskettes Return to use the default density 2mb Troubleshooting PIN Assignments Figure A-1 Serial Connector Pin NumberingTXD DTE Transceiver DO-S Slct Startup Messages Appendix B Startup Messages Monitor Utility You can access the monitor in either of the following waysContinuous Self-Test and Initial Boot Source parameters Set the Auto-reboot parameter to Boot monitorNonfunctional Dump Procedures on Memory dumps, refer to Memory Dump Procedures on-2 on page 1-4. The switch is recessed into a round hole to Become nonfunctional, enter the following commandSyntax BT From memory location Procedures onUsing this menu, refer to , Configuration Filename and address parameters specify the nameDescription Repeats the previous command On-line Technical Services3Com Bulletin Board Service 3ComBBS Technical SupportPress Return to see the ThreeComForum main menu Country Telephone Number Hong Kong 852 2537 44 1442 408 727 Appendix D Technical Support For Repair Returning ProductsSender’s expense To obtain an RMA number, call or fax 10/25/95 Numerics IndexCover Index Index Index Index Limited Warranty Bayfront Plaza Santa Clara, CA 408 764-5000 1/1/94