ADTRAN MP-118, MP-114 manual Configuring the MediaPack, Embedded Web Server Management Tool

Page 10

MP-11x & Microsoft Office Communications Server 2007

3 Configuring the MediaPack

The gateway is supplied with the application software residing on its flash memory (set to factory default parameters).

Note: This guide assumes that the gateway is running firmware version 5.0. If you are running an earlier version, please update the version to 5.0 (available on AudioCodes' Web site -- refer to Section 3.3.1.1 on page 17).

3.1Embedded Web Server Management Tool

The MediaPack gateway contains an embedded HTTP-based server that provides a user- friendly, client Web interface for gateway configuration and management.

3.1.1Accessing the Embedded Web Server

The MediaPack's Embedded Web Server is initially accessed using the default IP address (10.1.10.11), login user name ('Admin'), and login password ('Admin').

Note: Ensure that your MediaPack is in the same subnet as the PC running the Web browser. If not, refer to Section 3.2 on page 14 for assigning an IP address to the MediaPack.

¾To access the Embedded Web Server, take these 4 steps:

1.Open a standard Web-browsing application such as Microsoft™ Internet Explorer™ (Version 6.0 or higher) or Netscape™ Navigator™ (Version 7.2 or higher).

2.In the Web browser's URL address field, enter the IP address of the gateway; the Embedded Web Server’s ‘Enter Network Password’ screen appears, as shown in the figure below:

Figure 3-1: Enter Network Password Screen

3.Enter the case-sensitive, default username and password. You can later change the login user name and password, as described in Section 3.1.3 on page 12.

4.Click OK; the Embedded Web Server is accessed, displaying the ‘Quick Setup’ screen.

Quick Installation Guide

10

Document #: LTRT-26301

Image 10

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Customer Support TrademarksWeee EU Directive Abbreviations and TerminologyRelated Documentation Document # Manual NameIntroduction Network Architecture with PBXMP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start¾ To access the Embedded Web Server, take these 4 steps Configuring the MediaPackAccessing the Embedded Web Server Embedded Web Server Management ToolNavigating the Embedded Web Server MediaPack Web Interface AreasChanging Login Username and Password ¾ To change the user name and password, take these 3 stepsSearching for ini file Parameters Searched Result ScreenAssigning an IP Address to the MediaPack Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps New Client buttonAssigning an IP Address Using CLI via RS-232 Adding a BootP ClientAssigning an IP Address using Http Quick Setup ScreenUsing the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Configuration File Screen Modifying Parameters Specific to Site DeploymentUsing the Embedded Web Server Defining Mediation Servers IP Address¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBXDefining Voice Coders ¾ To define the coder, take these 3 stepsNumber Manipulation Parameters Description Parameter DescriptionDialing Plan Notations Description Example Source IPNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 stepsDefining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps¾ To enable Caller ID, take these 3 steps Enabling Caller IDDefining SIP Transport Type ¾ To define the SIP transport type, take these 3 stepsDefining Disconnect on Broken Connection 19 General Parameters ScreenDefining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage DialingDefining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp AttributeBacking Up Configuration Settings ¾ To save the ini file on your PC, take these 6 stepsMonitoring the Gateway Front-Panel LEDs¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Restoring Parameters to Factory Default Settings TroubleshootingGeneral Troubleshooting Debugging using a Syslog Server¾ To configure the Syslog parameters, take these 7 steps Management Settings ScreenRegulatory Information Network Compatibility Telecommunication SafetyIndustry Canada Notice FCC StatementMediaPack MP-118 & MP-114