ADTRAN MP-114, MP-118 manual Introduction, Network Architecture with PBX

Page 7

Quick Installation Guide

1. Introduction

1 Introduction

This guide provides step-by-step instructions for quickly setting up AudioCodes' MediaPack (MP-118 and MP-114) Session Initiation Protocol (SIP) voice-over-IP (VoIP) gateways for intermediating between third-party, private branch exchanges (PBX) or various Public Switched Telephone Network (PSTN) interfaces, and Microsoft® Office Communications Server 2007 (Office Communications Server 2007). For further information regarding Office Communications Server 2007, refer to Microsoft's Web site (http://www.microsoft.com/uc).

The figure below illustrates a network architecture with a PBX. In this scenario, the AudioCodes' gateway connects to the PBX using analog lines (FXO), and to Office Communications Server 2007 through Microsoft® Mediation Server (Mediation Server) on the IP network. The MediaPack gateways ensure interoperability with leading, third-party PBXs.

Figure 1-1: Network Architecture with PBX

The figure below illustrates a network architecture that provides a direct connection to the PSTN network. In this scenario, the AudioCodes' gateway connects to PSTN using analog lines. At the other end, the gateway connects to Office Communications Server 2007 through Mediation Server on the IP network.

Figure 1-2: Network Architecture with PSTN Interface

Version 5.0

7

September 2007

Image 7
Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Abbreviations and Terminology TrademarksWeee EU Directive Customer SupportDocument # Manual Name Related DocumentationNetwork Architecture with PBX IntroductionMP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPackEmbedded Web Server Management Tool Configuring the MediaPackAccessing the Embedded Web Server ¾ To access the Embedded Web Server, take these 4 stepsMediaPack Web Interface Areas Navigating the Embedded Web Server¾ To change the user name and password, take these 3 steps Changing Login Username and PasswordSearched Result Screen Searching for ini file ParametersNew Client button Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address to the MediaPackAdding a BootP Client Assigning an IP Address Using CLI via RS-232Quick Setup Screen Assigning an IP Address using HttpUsing the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Modifying Parameters Specific to Site Deployment Configuration File ScreenDefining Mediation Servers IP Address Using the Embedded Web Server¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps¾ To define the coder, take these 3 steps Defining Voice CodersParameter Description Number Manipulation Parameters DescriptionSource IP Dialing Plan Notations Description ExampleNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision¾ To define Automatic Dialing, take these 4 steps Defining Automatic DialingEnabling Caller ID ¾ To enable Caller ID, take these 3 steps¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type19 General Parameters Screen Defining Disconnect on Broken Connection¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload TypeEnabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps¾ To define the Channel Select mode, take these 3 steps Defining Channel Select ModeDisabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration SettingsFront-Panel LEDs Monitoring the Gateway¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Debugging using a Syslog Server TroubleshootingGeneral Troubleshooting Restoring Parameters to Factory Default SettingsManagement Settings Screen ¾ To configure the Syslog parameters, take these 7 stepsRegulatory Information FCC Statement Telecommunication SafetyIndustry Canada Notice Network CompatibilityMediaPack MP-118 & MP-114