ADTRAN MP-114 Defining SIP Transport Type, ¾ To define the SIP transport type, take these 3 steps

Page 31

Quick Installation Guide

3. Configuring the MediaPack

3.3.2.8Defining SIP Transport Type

The procedure below describes how to configure the SIP transport type. You may need to change the gateway's SIP transport type from UDP (default) to TCP, since this is the transport type used by Mediation Server.

¾To define the SIP transport type, take these 3 steps:

1.Open the ‘General Parameters’ screen (Protocol Management menu > Protocol Definition > General Parameters).

Figure 3-18: General Parameters Screen

2

2.From the ‘SIP Transport Type' drop-down list, select 'TCP'.

3.Click the Submit button to save your changes.

Version 5.0

31

September 2007

Image 31

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Abbreviations and Terminology TrademarksWeee EU Directive Customer SupportDocument # Manual Name Related DocumentationNetwork Architecture with PBX IntroductionMP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPackEmbedded Web Server Management Tool Configuring the MediaPackAccessing the Embedded Web Server ¾ To access the Embedded Web Server, take these 4 stepsMediaPack Web Interface Areas Navigating the Embedded Web Server¾ To change the user name and password, take these 3 steps Changing Login Username and PasswordSearched Result Screen Searching for ini file ParametersNew Client button Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address to the MediaPackAdding a BootP Client Assigning an IP Address Using CLI via RS-232Quick Setup Screen Assigning an IP Address using HttpUsing the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Modifying Parameters Specific to Site Deployment Configuration File ScreenDefining Mediation Servers IP Address Using the Embedded Web Server¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps¾ To define the coder, take these 3 steps Defining Voice CodersParameter Description Number Manipulation Parameters DescriptionSource IP Dialing Plan Notations Description ExampleNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision¾ To define Automatic Dialing, take these 4 steps Defining Automatic DialingEnabling Caller ID ¾ To enable Caller ID, take these 3 steps¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type19 General Parameters Screen Defining Disconnect on Broken Connection¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload TypeEnabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps¾ To define the Channel Select mode, take these 3 steps Defining Channel Select ModeDisabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration SettingsFront-Panel LEDs Monitoring the Gateway¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Debugging using a Syslog Server TroubleshootingGeneral Troubleshooting Restoring Parameters to Factory Default SettingsManagement Settings Screen ¾ To configure the Syslog parameters, take these 7 stepsRegulatory Information FCC Statement Telecommunication SafetyIndustry Canada Notice Network CompatibilityMediaPack MP-118 & MP-114