ADTRAN MP-114, MP-118 manual Defining Channel Select Mode

Page 35

Quick Installation Guide

3. Configuring the MediaPack

3.3.2.12 Defining Channel Select Mode

Channel select modes determine the method in which new IP-to-Tel calls (i.e., calls from OCS clients to PBX/PSTN phones) are assigned to gateway ports (i.e., channels). It is recommended to select the Cyclic Ascending mode, which selects the next available channel in an ascending cycle order.

¾To define the Channel Select mode, take these 3 steps:

1.Open the 'General' screen (Protocol Management menu > Protocol Definition > General Parameters).

Figure 3-22: General Screen

2

2.From the 'Channel Select Mode' drop-down list, select 'Cyclic Ascending'.

3.Click the Submit button to save your changes.

Version 5.0

35

September 2007

Image 35

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Abbreviations and Terminology TrademarksWeee EU Directive Customer SupportDocument # Manual Name Related DocumentationNetwork Architecture with PBX IntroductionMP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPackEmbedded Web Server Management Tool Configuring the MediaPackAccessing the Embedded Web Server ¾ To access the Embedded Web Server, take these 4 stepsMediaPack Web Interface Areas Navigating the Embedded Web Server¾ To change the user name and password, take these 3 steps Changing Login Username and PasswordSearched Result Screen Searching for ini file ParametersNew Client button Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address to the MediaPackAdding a BootP Client Assigning an IP Address Using CLI via RS-232Quick Setup Screen Assigning an IP Address using HttpObtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Modifying Parameters Specific to Site Deployment Configuration File ScreenDefining Mediation Servers IP Address Using the Embedded Web Server¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps¾ To define the coder, take these 3 steps Defining Voice CodersParameter Description Number Manipulation Parameters DescriptionSource IP Dialing Plan Notations Description ExampleNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision¾ To define Automatic Dialing, take these 4 steps Defining Automatic DialingEnabling Caller ID ¾ To enable Caller ID, take these 3 steps¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type19 General Parameters Screen Defining Disconnect on Broken Connection¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload TypeEnabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps¾ To define the Channel Select mode, take these 3 steps Defining Channel Select ModeDisabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration SettingsFront-Panel LEDs Monitoring the Gateway¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Debugging using a Syslog Server TroubleshootingGeneral Troubleshooting Restoring Parameters to Factory Default SettingsManagement Settings Screen ¾ To configure the Syslog parameters, take these 7 stepsRegulatory Information FCC Statement Telecommunication SafetyIndustry Canada Notice Network CompatibilityMediaPack MP-118 & MP-114