ADTRAN MP-114, MP-118 manual ¾ To configure the Syslog parameters, take these 7 steps

Page 41

Quick Installation Guide

6. Troubleshooting

¾To configure the Syslog parameters, take these 7 steps:

1.Open the ‘Management Settings’ screen (Advanced Configuration menu > Management Settings); the ‘Management Settings’ screen is displayed.

Figure 6-1: Management Settings Screen

2 3 4

5

2.In the 'Syslog Server IP Address' field, enter the Syslog's IP address. Note that the Syslog server's IP address must correspond to the network environment in which the Syslog server is installed.

3.In the 'Syslog Server Port' field, enter the UDP port number (default port is 514).

4.From the 'Enable Syslog' drop-down list, enable the Syslog feature by selecting 'Enable'.

5.In the 'Activity Types to Report' group, select the Web operations that you want logged to the Syslog server.

6.To define the messages based on severity level that you want sent to the Syslog server, open the ‘General Parameters’ screen (Protocol Management menu > Advanced Parameters > General Parameters), and then from the 'Debug Level' drop-down list, select '5' (i.e., all reports with severity level 5 are sent to the Syslog server).

7.To enable additional call information sent to the Syslog, in the 'CDR Report Level' drop-down list, select 'End Call'

Version 5.0

41

September 2007

Image 41

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Weee EU Directive TrademarksCustomer Support Abbreviations and TerminologyDocument # Manual Name Related DocumentationNetwork Architecture with PBX IntroductionMP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPackAccessing the Embedded Web Server Configuring the MediaPack¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management ToolMediaPack Web Interface Areas Navigating the Embedded Web Server¾ To change the user name and password, take these 3 steps Changing Login Username and PasswordSearched Result Screen Searching for ini file Parameters¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address using BootPAssigning an IP Address to the MediaPack New Client buttonAdding a BootP Client Assigning an IP Address Using CLI via RS-232Quick Setup Screen Assigning an IP Address using HttpObtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Modifying Parameters Specific to Site Deployment Configuration File ScreenDefining Mediation Servers IP Address Using the Embedded Web Server¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps¾ To define the coder, take these 3 steps Defining Voice CodersParameter Description Number Manipulation Parameters DescriptionSource IP Dialing Plan Notations Description ExampleNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision¾ To define Automatic Dialing, take these 4 steps Defining Automatic DialingEnabling Caller ID ¾ To enable Caller ID, take these 3 steps¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type19 General Parameters Screen Defining Disconnect on Broken Connection¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload TypeEnabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps¾ To define the Channel Select mode, take these 3 steps Defining Channel Select ModeDisabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration SettingsFront-Panel LEDs Monitoring the Gateway¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step General Troubleshooting TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog ServerManagement Settings Screen ¾ To configure the Syslog parameters, take these 7 stepsRegulatory Information Industry Canada Notice Telecommunication SafetyNetwork Compatibility FCC StatementMediaPack MP-118 & MP-114