ADTRAN MP-114, MP-118 manual Defining Voice Coders, ¾ To define the coder, take these 3 steps

Page 23

Quick Installation Guide

3. Configuring the MediaPack

3.3.2.3Defining Voice Coders

The gateway communicates with Mediation Server using either the G.711 A-law or G.711 µ-law coder. You can change the default coder using the gateway's Embedded Web Server.

¾To define the coder, take these 3 steps:

1.Open the ‘Coders' screen (Protocol Management menu > Protocol Definition > Coders).

Figure 3-11: Coders Screen

2.From the 'Coder Name' drop-down list, select the required coder.

3.Reset the gateway by clicking the Maintenance button on the main menu bar. Select the 'BURN' option to burn the configuration to flash memory, and then click the Reset button.

3.3.2.4Translating Numbers From / To E.164 Using Manipulation Tables for PBX/PSTN Connectivity

The Embedded Web Server's Manipulation tables provide the ability to translate (normalize) numbers dialed in standard E.164 format to various formats and vice versa. Manipulation is necessary for your dial plan as Office Communications Server 2007 uses the standard E.164 format while your PBX or PSTN implements other number formats for dialing.

Due to Office Communications Server 2007normalization rules, the gateway may need to perform number manipulation for outbound calls (i.e., calls received from OCS client via Office Communications Server 2007) and inbound calls (i.e., calls destined for OCS client). If the gateway is connected to a PBX or directly to the PSTN, the gateway may need to perform number manipulations for the called and/or calling number to match the PBX or PSTN interfaces dialing rules or to match Office Communications Server 2007 E.164 format.

Manipulation number configuration examples are provided for inbound and outbound calls in Section 3.3.2.4.2 on page 26.

Version 5.0

23

September 2007

Image 23

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Abbreviations and Terminology TrademarksWeee EU Directive Customer SupportDocument # Manual Name Related DocumentationNetwork Architecture with PBX IntroductionMP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPackEmbedded Web Server Management Tool Configuring the MediaPackAccessing the Embedded Web Server ¾ To access the Embedded Web Server, take these 4 stepsMediaPack Web Interface Areas Navigating the Embedded Web Server¾ To change the user name and password, take these 3 steps Changing Login Username and PasswordSearched Result Screen Searching for ini file ParametersNew Client button Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address to the MediaPackAdding a BootP Client Assigning an IP Address Using CLI via RS-232Quick Setup Screen Assigning an IP Address using HttpObtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Modifying Parameters Specific to Site Deployment Configuration File ScreenDefining Mediation Servers IP Address Using the Embedded Web Server¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps¾ To define the coder, take these 3 steps Defining Voice CodersParameter Description Number Manipulation Parameters DescriptionSource IP Dialing Plan Notations Description ExampleNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision¾ To define Automatic Dialing, take these 4 steps Defining Automatic DialingEnabling Caller ID ¾ To enable Caller ID, take these 3 steps¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type19 General Parameters Screen Defining Disconnect on Broken Connection¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload TypeEnabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps¾ To define the Channel Select mode, take these 3 steps Defining Channel Select ModeDisabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration SettingsFront-Panel LEDs Monitoring the Gateway¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Debugging using a Syslog Server TroubleshootingGeneral Troubleshooting Restoring Parameters to Factory Default SettingsManagement Settings Screen ¾ To configure the Syslog parameters, take these 7 stepsRegulatory Information FCC Statement Telecommunication SafetyIndustry Canada Notice Network CompatibilityMediaPack MP-118 & MP-114