ADTRAN MP-118, MP-114 manual Monitoring the Gateway, Front-Panel LEDs

Page 38

MP-11x & Microsoft Office Communications Server 2007

5 Monitoring the Gateway

The gateway provides several methods to monitor various operating statuses:

Monitoring the gateway's front-panel chassis LEDs (refer to Section 5.1).

Monitoring the gateway's channels using the Embedded Web Server (refer to Section 5.2 on page 39).

5.1Front-Panel LEDs

The gateway provides various operating LEDs on its front-panel, as described in the table below:

Table 5-1: Description of Gateway's Front Panel LEDs

LED	Type		Color	State		Definition

Ready	Device		Green	On		Device powered, self-test OK.
	Status
	Status		Orange	Blinking		Software loading/Initialization.
			Orange	Blinking		Software loading/Initialization.
			Red	On		Malfunction.
Uplink	Ethernet		Green	On		Valid 10/100 Base-TX Ethernet connection.
	Link Status
	Link Status		Red	On		No uplink.
			Red	On		No uplink.
Power	Power		Green	On		Power is currently being supplied to the gateway.
	Supply		--	Off		Either there’s a failure / disruption in the AC power
	Status		--	Off		Either there’s a failure / disruption in the AC power
	Status					supply or power is currently not being supplied to the
						supply or power is currently not being supplied to the
						gateway through the AC power supply entry.

Fail	Failure		Red	On		Failure (fatal error) or system initialization.
	Indication		--	Off		No traffic.
			--	Off		No traffic.

Channels	Telephone /		Green	On		The FXO gateway off-hooks the line towards the PBX.
Status	PBX		Green	Blinking		Indicates an incoming call, before answering.
	Interface		Green	Blinking		Indicates an incoming call, before answering.

			Red	On		Line malfunction.
			--	Off		Normal on hook position.


		Note:	The front panels of the MP-114 and MP-118 are similar except for the number of
			Channels Status LEDs.

Quick Installation Guide

38

Document #: LTRT-26301

Image 38

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Customer Support TrademarksWeee EU Directive Abbreviations and TerminologyRelated Documentation Document # Manual NameIntroduction Network Architecture with PBXMP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start¾ To access the Embedded Web Server, take these 4 steps Configuring the MediaPackAccessing the Embedded Web Server Embedded Web Server Management ToolNavigating the Embedded Web Server MediaPack Web Interface AreasChanging Login Username and Password ¾ To change the user name and password, take these 3 stepsSearching for ini file Parameters Searched Result ScreenAssigning an IP Address to the MediaPack Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps New Client buttonAssigning an IP Address Using CLI via RS-232 Adding a BootP ClientAssigning an IP Address using Http Quick Setup ScreenObtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Configuration File Screen Modifying Parameters Specific to Site DeploymentUsing the Embedded Web Server Defining Mediation Servers IP Address¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBXDefining Voice Coders ¾ To define the coder, take these 3 stepsNumber Manipulation Parameters Description Parameter DescriptionDialing Plan Notations Description Example Source IPNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 stepsDefining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps¾ To enable Caller ID, take these 3 steps Enabling Caller IDDefining SIP Transport Type ¾ To define the SIP transport type, take these 3 stepsDefining Disconnect on Broken Connection 19 General Parameters ScreenDefining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage DialingDefining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp AttributeBacking Up Configuration Settings ¾ To save the ini file on your PC, take these 6 stepsMonitoring the Gateway Front-Panel LEDs¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Restoring Parameters to Factory Default Settings TroubleshootingGeneral Troubleshooting Debugging using a Syslog Server¾ To configure the Syslog parameters, take these 7 steps Management Settings ScreenRegulatory Information Network Compatibility Telecommunication SafetyIndustry Canada Notice FCC StatementMediaPack MP-118 & MP-114