ADTRAN MP-118, MP-114 manual MP-11x & Microsoft Office Communications Server

Page 8

MP-11x & Microsoft Office Communications Server 2007

The AudioCodes' MP-11x FXO gateway can be integrated in the Office Communications Server

2007 / Unified Communications (UC) environments, by implementing one of the following options:

One-to-One:each PBX line connected to an FXO port on the gateway, serves one Office Communications Server 2007 user / endpoint (OCS client) and is defined for automatic dialing for this OCS client. A PBX or PSTN user that wants to call the OCS client, dials the OCS client's PBX line number.

One-to-Many:group of PBX lines connected to the gateway serves all the OCS clients. When a new call is received from the PBX, the gateway answers the call and performs one of the following:

•Plays a dial tone, after which the caller can dial the OCS client's extension number.

•Plays a pre-recorded greeting message to the caller, requesting the caller to dial the desired OCS client (for example, “Welcome company X, please dial the desired extension number”). The gateway acts as an interactive voice response (IVR) system. For this option, you may need to upload a pre-recorded tone file (refer the User's Manual).

PBX-Sends-Digits:group of Direct Inward Dialing (DID) PBX lines connected to the gateway serves all the OCS clients. When a new call is received from the PBX, the gateway answers the call, and then the PBX automatically sends the OCS client number as it was received.

Quick Installation Guide

8

Document #: LTRT-26301

Image 8

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Trademarks Weee EU DirectiveCustomer Support Abbreviations and TerminologyRelated Documentation Document # Manual NameIntroduction Network Architecture with PBXMP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick StartConfiguring the MediaPack Accessing the Embedded Web Server¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management ToolNavigating the Embedded Web Server MediaPack Web Interface AreasChanging Login Username and Password ¾ To change the user name and password, take these 3 stepsSearching for ini file Parameters Searched Result ScreenAssigning an IP Address using BootP ¾ To assign an IP address using BootP, take these 3 stepsAssigning an IP Address to the MediaPack New Client buttonAssigning an IP Address Using CLI via RS-232 Adding a BootP ClientAssigning an IP Address using Http Quick Setup ScreenObtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Configuration File Screen Modifying Parameters Specific to Site DeploymentUsing the Embedded Web Server Defining Mediation Servers IP Address¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBXDefining Voice Coders ¾ To define the coder, take these 3 stepsNumber Manipulation Parameters Description Parameter DescriptionDialing Plan Notations Description Example Source IPNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 stepsDefining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps¾ To enable Caller ID, take these 3 steps Enabling Caller IDDefining SIP Transport Type ¾ To define the SIP transport type, take these 3 stepsDefining Disconnect on Broken Connection 19 General Parameters ScreenDefining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage DialingDefining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp AttributeBacking Up Configuration Settings ¾ To save the ini file on your PC, take these 6 stepsMonitoring the Gateway Front-Panel LEDs¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Troubleshooting General TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog Server¾ To configure the Syslog parameters, take these 7 steps Management Settings ScreenRegulatory Information Telecommunication Safety Industry Canada NoticeNetwork Compatibility FCC StatementMediaPack MP-118 & MP-114