ADTRAN MP-118 manual Enabling One-Stage Dialing, ¾ To enable one-stage dialing, take these 3 steps

Page 34

MP-11x & Microsoft Office Communications Server 2007

3.3.2.11 Enabling One-Stage Dialing

One-stage dialing is when the gateway receives an IP-to-Tel call, off-hooks the PBX line connected to the PBX / PSTN telephone, and then immediately dials the destination telephone number. In other words, the OCS client (i.e., IP caller) doesn't dial the PSTN number upon hearing a dial tone.

¾To enable one-stage dialing, take these 3 steps:

1.Open the ‘FXO Settings’ screen (Protocol Management menu > Advanced Applications > FXO Settings); the ‘FXO Settings’ screen is displayed.

Figure 3-21: FXO Settings Screen

2

2.From the 'Dialing Mode' drop-down list, select 'One Stage'.

3.Click the Submit button to save your changes.

Quick Installation Guide

34

Document #: LTRT-26301

Image 34

Contents MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Customer Support TrademarksWeee EU Directive Abbreviations and TerminologyRelated Documentation Document # Manual NameIntroduction Network Architecture with PBXMP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start¾ To access the Embedded Web Server, take these 4 steps Configuring the MediaPackAccessing the Embedded Web Server Embedded Web Server Management ToolNavigating the Embedded Web Server MediaPack Web Interface AreasChanging Login Username and Password ¾ To change the user name and password, take these 3 stepsSearching for ini file Parameters Searched Result ScreenAssigning an IP Address to the MediaPack Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps New Client buttonAssigning an IP Address Using CLI via RS-232 Adding a BootP ClientAssigning an IP Address using Http Quick Setup ScreenUsing the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Configuration File Screen Modifying Parameters Specific to Site DeploymentUsing the Embedded Web Server Defining Mediation Servers IP Address¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBXDefining Voice Coders ¾ To define the coder, take these 3 stepsNumber Manipulation Parameters Description Parameter DescriptionDialing Plan Notations Description Example Source IPNumber Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 stepsDefining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps¾ To enable Caller ID, take these 3 steps Enabling Caller IDDefining SIP Transport Type ¾ To define the SIP transport type, take these 3 stepsDefining Disconnect on Broken Connection 19 General Parameters ScreenDefining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage DialingDefining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp AttributeBacking Up Configuration Settings ¾ To save the ini file on your PC, take these 6 stepsMonitoring the Gateway Front-Panel LEDs¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Restoring Parameters to Factory Default Settings TroubleshootingGeneral Troubleshooting Debugging using a Syslog Server¾ To configure the Syslog parameters, take these 7 steps Management Settings ScreenRegulatory Information Network Compatibility Telecommunication SafetyIndustry Canada Notice FCC StatementMediaPack MP-118 & MP-114