Silex technology SX-500-1402 manual Configuration Methods

Page 18

∙Flow Control

In addition to the above parameters, the Serial Device Server allows you to configure numerous other capabilities. These other capabilities provide you with the unparalleled flexibility to use the Serial Device Server on virtually any 802.11 or Ethernet network with a wide range of serial devices.

Configuration Methods

There are two ways to configure the Serial Device Server:

∙Internal Web Pages (HTTP). You can use any standard web browser to access the Serial Device Server internal web pages. These web pages provide an easy-to-use graphical interface for configuring the Serial Device Server. In order to use the internal web pages for the first time, you must assign the Serial Device Server IP address using some other method (for example, DHCP or arp/ping). This initial IP address assignment need only be done one time.

∙Internal Command Console. The internal command console provides a sophisticated command line interface for advanced users to configure the Serial Device Server. It can be accessed by connecting a serial cable to the serial port and using console mode switching as descried in chapter 4. Once the IP address has been assigned, the internal command console can also be accessed via TELNET, or via the internal web pages. NOTE: when operating in a FIPS 140-2 approved mode, the console is not available via the serial port.

If you have a Serial Device Server wireless model, Silex recommends that you temporarily plug the Serial Device into a wired Ethernet network during the configuration process. Although it is possible to configure the Serial Device Server with a completely wireless setup, it is much simpler to perform the process using a wired Ethernet connection. This is primarily because the wireless security on most wireless networks prevents the addition of a new wireless device unless all security parameters are first entered into that device. As a result, you must set up a temporary dedicated ad hoc wireless network in order to configure the Serial Device Server in a completely wireless environment (refer to the step 4 in the First Time IP Address Configuration section of this chapter for instructions on how to set up the Serial Device Server using a completely wireless Ad Hoc environment). This is required when entering security encryption keys (RSA private key or WPA2-PSK).

Configuring the Serial Device Server using each of the above methods is described in the following sections of this chapter.

Page 12

Silex

Configuring the Serial Device Server

 

Part Number 140-00188-210A

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents SX-500-1402 Serial Device Server Trademarks Page Contents Figures Contents Silex Part Number 140-00188-210A Safety Precautions About This Reference GuideEmissions Disclaimer Revision History 2009.08.13 Lee Aydelotte Initial ReleaseIntroduction SX-500LED Logical PortsPort Name Description FIPS-140-2 Interface Physical Logical InterfaceConfiguration Required SettingWPA2 AES-CCMP Https Physical Protection Secure OperationInstalling the Serial Device Server Hardware Verify Package ContentsInstalling the Serial Device Server RS-232 connector pinouts and cabling Monitoring Serial Device Server Status Status Monitors Function StateTCP/IP Settings Chapter Configuring the Serial Device ServerBasic Configuration Requirements Wireless Configuration SettingsConfiguration Methods First-Time IP Address Configuration Ping ipaddress Using a Web Browser to Configure the Serial Device Server Silex Authentication Server Certificate You can skip the remainder of this chapter AD-HOC Disabled Init ExitChapter Using the Serial Device Server with Your Application Serial Port EmulatorRaw TCP connection Telnet ipaddress portnumberECable Mode RFC 2217 Remote Modem Control SupportPrint Server Mode Console Mode SwitchingAT Commands SET Port S1 Filter ATFactory Default Settings Parameter Description Chapter Advanced ConfigurationFactory Default Settings CTS/RTSModifying TCP/IP Settings Parameter Description Settings Default SettingUsing AT Modem Commands TCP/IP Settings ParameterDNS Standard AT Commands Supported AT Commands Parameter DescriptionParameter Command Description Extended AT Commands Parameter DescriptionAT#Cset nw ssid silex#Csave Response Codes Response Codes Numeric Code DescriptionChapter Troubleshooting Email Tech support support@silexamerica.com Chapter Product Specifications Product Specifications ComponentRadio Performance Specifications Parameter TCP Port Connections Parameter SpecificationsTCP Port Connections Port Destination DeviceEAP Appendix a Advanced Security ConfigurationPSK Ttls LeapWEP Key Value Wireless Security Only Encryption Mode Wireless Security OnlyKey Selection Wireless Security Only Pre-Shared Key Wireless Security OnlyAuthentication Attempts Wireless Authentication Type Wireless Security OnlyWired Authentication Type Wired Ethernet Networks Only PasswordProduct Specifications Silex Part Number 140-00188-210A Network Commands Description Appendix B Console CommandsWireless and Network Security Commands Signal Quality Signal Strength = Noise LevelCommand Description TLS PSKSET NW Ethauth Ttls TLS Peap SET NW KEY# SET NW RTS Wifi RTS Threshold =CL NW BSsid SET NW CertcnSET NW Certkey SET NW CERTCN2SET NW Certexp SET NW IDSET NW Wpagroup Enable Disable SET NW Inap PAPMSCHAPV2SET NW Realm Port Commands Description Port CommandsSET NW Reset XON/XOFFCL Port S1 JOB Server Information CommandsServer Information Commands Description SET Port S1 Size 7SET Snmp LOCation string SET SERVEr NAme NameSET Snmp CONtact String SH SerialService Commands Service Commands DescriptionTEXTP1 TwcffffffBINARYP1 TWCFFFFFFP14String Commands String CommandsEnter LANGUAGE= TCP/IP CommandsTCP/IP Commands Description POSTSCRIPT\0ASET IP BAnner ENable DIsable All hosts permitted accessSET ARP ENable DIsable SET IP Chksum ENable DIsableSET IP Http Auto Bootp Rarp Dhcp StaticSET IP FTP SET IP LPDSET IP TCP SET IP TftpSH IP AutoXxxxxxS1A 9100 XxxxxxS1B 3001 Firmware Update Firmware Update Command DescriptionMiscellaneous Commands Help CommandsMiscellaneous Commands Description Console Commands Silex Part Number 140-00188-210A Appendix C Firmware Update Procedures Firmware Update Procedures Silex Part Number 140-00188-210A Appendix D Safety and Regulatory Notices Information for United States UsersInformation for Canadian Users IC notice SX-500  FCC ID N6C-SX10WGInformation for European Users SX-500 Declaration of Conformity CE SX-500Silex Technology Europe GmbH Appendix E Silex Contact InformationSilex Technology America, Inc Silex Technology Beijing, IncSilex Technology America, Inc

SX-500-1402 specifications

The Silex Technology SX-500-1402 is an advanced industrial wireless module designed for seamless integration into various applications requiring high-performance wireless connectivity. This module is particularly renowned for its robust features, making it ideal for use in automation, healthcare, and smart city applications.

One of the main features of the SX-500-1402 is its dual-band Wi-Fi capability, which operates on both 2.4 GHz and 5 GHz frequencies. This not only provides flexibility for different environments but also enhances the overall performance by reducing interference and optimizing data throughput. The module supports Wi-Fi 5 (802.11ac), enabling high-speed data transmission and ensuring reliable connectivity even in crowded environments.

Another key aspect of the SX-500-1402 is its compact size and lightweight design, offering an excellent solution for space-constrained applications. The module features a PCB form factor that facilitates easy integration into diverse devices while minimizing additional footprint.

The SX-500-1402 boasts advanced security features, including WPA3 support, ensuring encryption and secure data transmission across networks. This is a critical requirement for applications in healthcare and finance, where safeguarding sensitive information is paramount. Furthermore, the module supports secure boot and firmware updates, further enhancing its security posture.

In terms of power management, the Silex module is designed for energy efficiency, making it suitable for battery-powered applications. It features various power-saving modes that help to extend battery life without compromising performance, enabling devices to operate for longer periods without frequent recharging.

The SX-500-1402 also integrates seamlessly with diverse host interfaces, such as UART, SPI, and I2C, facilitating easy connectivity to microcontrollers and other devices. This versatility makes it an ideal choice for developers looking to prototype and bring their IoT solutions to market swiftly.

Key specifications of the SX-500-1402 include a maximum data rate of 867 Mbps in the 5 GHz band, operating temperature range from -20 to 70 degrees Celsius, and an extended range due to its MIMO (Multiple Input, Multiple Output) technology, which further enhances performance in environments with obstacles.

In summary, the Silex Technology SX-500-1402 is an exceptional choice for applications requiring reliable, high-speed wireless communication. With its advanced features, robust security measures, and versatile integration options, it stands out as a premier solution in the industrial wireless module landscape.
Top Page Image Contents