Silex technology SX-500-1402 manual SET NW Inap PAPMSCHAPV2, SET NW Realm

Page 51

Command

Description

SET NW INAP

Sets EAP inner-authentication protocol

 

The possible protocols are PAP and MSCHAP_V2; the default value is PAP.

 

Format:

 

 

SET NW INAP

[PAPMSCHAP_V2]

SH NW INAP

Shows the inner authentication mode

 

The deprecated command SH NW TTAP also returns this data.

 

Sample output:

 

 

Authentication protocol = PAP

SET NW REALM

Sets the realm portion of the 802.1x EAP authentication ID

 

This value can also be set with the ID command.

 

The default value is null.

 

 

Format:

 

 

SET NW REALM

<realm>

SH NW REALM

Shows the realm associated with the authentication ID, if applicable.

 

The default value is null (blank) string.

 

The deprecated command SH NW TTRE also returns this data.

 

Sample output:

 

 

Somewhere

 

SET NW

Enable or disable WPA group key mode.

WPAGROUP

If enabled, group keys can be used for data link encryption.

 

 

The default value is disabled.

 

Sample output:

 

 

SET NW WPAGROUP [ENABLE DISABLE]

 

NOTE: For FIPS 140-2 approved operation, this parameter must

 

be DISABLED.

 

SH NW

Shows state of WPA auto connect flag

WPAAUTO

Sample output:

 

 

WPA-AUTO Enabled

SH NW

Shows state of the allow WPA group keys flag

WPAGROUP

Sample output:

 

 

WPA-GROUP Disabled.

SET NW WPAPSK

Sets WPA PSK pass phrase or hex key.

 

This value is only used if the authentication mode is WPA-PSK or WPA2-PSK. The

 

argument to this command is exactly 64 hex characters representing the 256 bit PSK

 

value.

 

 

Format:

 

SET NW WPAPSK <key>

Console Commands

Silex

Page 45

 

Part Number 140-00188-210A

 

Image 51
Contents SX-500-1402 Serial Device Server Trademarks Page Contents Figures Contents Silex Part Number 140-00188-210A Safety Precautions About This Reference GuideEmissions Disclaimer 2009.08.13 Lee Aydelotte Initial Release Revision HistorySX-500 IntroductionFIPS-140-2 Interface Physical Logical Interface Logical PortsPort Name Description LEDConfiguration Required SettingWPA2 AES-CCMP Https Secure Operation Physical ProtectionInstalling the Serial Device Server Hardware Verify Package ContentsInstalling the Serial Device Server RS-232 connector pinouts and cabling Status Monitors Function State Monitoring Serial Device Server StatusWireless Configuration Settings Chapter Configuring the Serial Device ServerBasic Configuration Requirements TCP/IP SettingsConfiguration Methods First-Time IP Address Configuration Ping ipaddress Using a Web Browser to Configure the Serial Device Server Silex Authentication Server Certificate You can skip the remainder of this chapter AD-HOC Init Exit DisabledSerial Port Emulator Chapter Using the Serial Device Server with Your ApplicationTelnet ipaddress portnumber Raw TCP connectionRFC 2217 Remote Modem Control Support ECable ModeConsole Mode Switching Print Server ModeSET Port S1 Filter AT AT CommandsCTS/RTS Chapter Advanced ConfigurationFactory Default Settings Factory Default Settings Parameter DescriptionParameter Description Settings Default Setting Modifying TCP/IP SettingsUsing AT Modem Commands TCP/IP Settings ParameterDNS AT Commands Parameter Description Standard AT Commands SupportedParameter Command Description Extended AT Commands Parameter DescriptionAT#Cset nw ssid silex#Csave Response Codes Numeric Code Description Response CodesChapter Troubleshooting Email Tech support support@silexamerica.com Chapter Product Specifications Product Specifications ComponentRadio Performance Specifications Parameter Port Destination Device Parameter SpecificationsTCP Port Connections TCP Port ConnectionsTtls Leap Appendix a Advanced Security ConfigurationPSK EAPPre-Shared Key Wireless Security Only Encryption Mode Wireless Security OnlyKey Selection Wireless Security Only WEP Key Value Wireless Security OnlyPassword Wireless Authentication Type Wireless Security OnlyWired Authentication Type Wired Ethernet Networks Only Authentication AttemptsProduct Specifications Silex Part Number 140-00188-210A Signal Quality Signal Strength = Noise Level Appendix B Console CommandsWireless and Network Security Commands Network Commands DescriptionCommand Description TLS PSKSET NW Ethauth Ttls TLS Peap SET NW KEY# SET NW Certcn Wifi RTS Threshold =CL NW BSsid SET NW RTSSET NW ID SET NW CERTCN2SET NW Certexp SET NW CertkeySET NW Wpagroup Enable Disable SET NW Inap PAPMSCHAPV2SET NW Realm XON/XOFF Port CommandsSET NW Reset Port Commands DescriptionSET Port S1 Size 7 Server Information CommandsServer Information Commands Description CL Port S1 JOBSH Serial SET SERVEr NAme NameSET Snmp CONtact String SET Snmp LOCation stringService Commands Description Service CommandsTWCFFFFFFP14 TwcffffffBINARYP1 TEXTP1String Commands String CommandsPOSTSCRIPT\0A TCP/IP CommandsTCP/IP Commands Description Enter LANGUAGE=SET IP Chksum ENable DIsable All hosts permitted accessSET ARP ENable DIsable SET IP BAnner ENable DIsableSET IP LPD Auto Bootp Rarp Dhcp StaticSET IP FTP SET IP HttpSET IP Tftp SET IP TCPSH IP AutoXxxxxxS1A 9100 XxxxxxS1B 3001 Firmware Update Command Description Firmware UpdateMiscellaneous Commands Help CommandsMiscellaneous Commands Description Console Commands Silex Part Number 140-00188-210A Appendix C Firmware Update Procedures Firmware Update Procedures Silex Part Number 140-00188-210A Information for United States Users Appendix D Safety and Regulatory Notices FCC ID N6C-SX10WG Information for Canadian Users IC notice SX-500Declaration of Conformity CE SX-500 Information for European Users SX-500Silex Technology Beijing, Inc Appendix E Silex Contact InformationSilex Technology America, Inc Silex Technology Europe GmbHSilex Technology America, Inc

SX-500-1402 specifications

The Silex Technology SX-500-1402 is an advanced industrial wireless module designed for seamless integration into various applications requiring high-performance wireless connectivity. This module is particularly renowned for its robust features, making it ideal for use in automation, healthcare, and smart city applications.

One of the main features of the SX-500-1402 is its dual-band Wi-Fi capability, which operates on both 2.4 GHz and 5 GHz frequencies. This not only provides flexibility for different environments but also enhances the overall performance by reducing interference and optimizing data throughput. The module supports Wi-Fi 5 (802.11ac), enabling high-speed data transmission and ensuring reliable connectivity even in crowded environments.

Another key aspect of the SX-500-1402 is its compact size and lightweight design, offering an excellent solution for space-constrained applications. The module features a PCB form factor that facilitates easy integration into diverse devices while minimizing additional footprint.

The SX-500-1402 boasts advanced security features, including WPA3 support, ensuring encryption and secure data transmission across networks. This is a critical requirement for applications in healthcare and finance, where safeguarding sensitive information is paramount. Furthermore, the module supports secure boot and firmware updates, further enhancing its security posture.

In terms of power management, the Silex module is designed for energy efficiency, making it suitable for battery-powered applications. It features various power-saving modes that help to extend battery life without compromising performance, enabling devices to operate for longer periods without frequent recharging.

The SX-500-1402 also integrates seamlessly with diverse host interfaces, such as UART, SPI, and I2C, facilitating easy connectivity to microcontrollers and other devices. This versatility makes it an ideal choice for developers looking to prototype and bring their IoT solutions to market swiftly.

Key specifications of the SX-500-1402 include a maximum data rate of 867 Mbps in the 5 GHz band, operating temperature range from -20 to 70 degrees Celsius, and an extended range due to its MIMO (Multiple Input, Multiple Output) technology, which further enhances performance in environments with obstacles.

In summary, the Silex Technology SX-500-1402 is an exceptional choice for applications requiring reliable, high-speed wireless communication. With its advanced features, robust security measures, and versatile integration options, it stands out as a premier solution in the industrial wireless module landscape.