Silex technology SX-500-1402 manual Set Ip Tcp, SET IP Tftp

Page 61

Command

Description

SET IP ROuter	Sets default router address
	The default value is 0.0.0.0.
	Format:
	SET IP ROuter	aa.bb.cc.dd
SET IP SUbnet	Sets IP subnet mask
	The default value is 0.0.0.0.
	Format:
	SET IP SUbnet	aa.bb.cc.dd
SET IP TCP	Enables or disables the raw TCP 9100 protocol
	The default value is Enable.
	Format:
	SET IP TCP	[ENable DIsable]
SET IP TELnet	Enables or disables Telnet protocol
	The default value is Enable.
	Format:
	SET IP TELnet [ENable DIsable]
SET IP TFTP	Enables or disables TFTP protocol
	The default value is Enable.
	Format:
	SET IP TFTP	[ENable DIsable ]
SET IP TImeout	Sets TCP inactivity timeout.
	If fast timeout is enabled, the timeout is calculated as seconds.
	If fast timeout is disabled, the timeout is calculated as minutes.
	The default value is 1 minute.
	Format:
	SET IP Timeout	n
SET IP WIndow	Sets TCP maximum window size in bytes
	The default value is 10240.
	Format:
	SET IP WIndow	nn

Console Commands	Silex	Page 55
	Part Number 140-00188-210A

Image 61

Contents

SX-500-1402 Serial Device Server Trademarks Page Contents Figures Contents Silex Part Number 140-00188-210A About This Reference Guide Safety PrecautionsEmissions Disclaimer 2009.08.13 Lee Aydelotte Initial Release Revision HistorySX-500 IntroductionPort Name Description Logical PortsLED FIPS-140-2 Interface Physical Logical InterfaceRequired Setting ConfigurationWPA2 AES-CCMP Https Secure Operation Physical ProtectionVerify Package Contents Installing the Serial Device Server HardwareInstalling the Serial Device Server RS-232 connector pinouts and cabling Status Monitors Function State Monitoring Serial Device Server StatusBasic Configuration Requirements Chapter Configuring the Serial Device ServerTCP/IP Settings Wireless Configuration SettingsConfiguration Methods First-Time IP Address Configuration Ping ipaddress Using a Web Browser to Configure the Serial Device Server Silex Authentication Server Certificate You can skip the remainder of this chapter AD-HOC Init Exit DisabledSerial Port Emulator Chapter Using the Serial Device Server with Your ApplicationTelnet ipaddress portnumber Raw TCP connectionRFC 2217 Remote Modem Control Support ECable ModeConsole Mode Switching Print Server ModeSET Port S1 Filter AT AT CommandsFactory Default Settings Chapter Advanced ConfigurationFactory Default Settings Parameter Description CTS/RTSParameter Description Settings Default Setting Modifying TCP/IP SettingsTCP/IP Settings Parameter Using AT Modem CommandsDNS AT Commands Parameter Description Standard AT Commands SupportedExtended AT Commands Parameter Description Parameter Command DescriptionAT#Cset nw ssid silex#Csave Response Codes Numeric Code Description Response CodesChapter Troubleshooting Email Tech support support@silexamerica.com Product Specifications Component Chapter Product SpecificationsRadio Performance Specifications Parameter TCP Port Connections Parameter SpecificationsTCP Port Connections Port Destination DevicePSK Appendix a Advanced Security ConfigurationEAP Ttls LeapKey Selection Wireless Security Only Encryption Mode Wireless Security OnlyWEP Key Value Wireless Security Only Pre-Shared Key Wireless Security OnlyWired Authentication Type Wired Ethernet Networks Only Wireless Authentication Type Wireless Security OnlyAuthentication Attempts PasswordProduct Specifications Silex Part Number 140-00188-210A Wireless and Network Security Commands Appendix B Console CommandsNetwork Commands Description Signal Quality Signal Strength = Noise LevelTLS PSK Command DescriptionSET NW Ethauth Ttls TLS Peap SET NW KEY# CL NW BSsid Wifi RTS Threshold =SET NW RTS SET NW CertcnSET NW Certexp SET NW CERTCN2SET NW Certkey SET NW IDSET NW Inap PAPMSCHAPV2 SET NW Wpagroup Enable DisableSET NW Realm SET NW Reset Port CommandsPort Commands Description XON/XOFFServer Information Commands Description Server Information CommandsCL Port S1 JOB SET Port S1 Size 7SET Snmp CONtact String SET SERVEr NAme NameSET Snmp LOCation string SH SerialService Commands Description Service CommandsBINARYP1 TwcffffffTEXTP1 TWCFFFFFFP14 String Commands String CommandsTCP/IP Commands Description TCP/IP CommandsEnter LANGUAGE= POSTSCRIPT\0ASET ARP ENable DIsable All hosts permitted accessSET IP BAnner ENable DIsable SET IP Chksum ENable DIsableSET IP FTP Auto Bootp Rarp Dhcp StaticSET IP Http SET IP LPDSET IP Tftp SET IP TCPAuto SH IPXxxxxxS1A 9100 XxxxxxS1B 3001 Firmware Update Command Description Firmware UpdateHelp Commands Miscellaneous CommandsMiscellaneous Commands Description Console Commands Silex Part Number 140-00188-210A Appendix C Firmware Update Procedures Firmware Update Procedures Silex Part Number 140-00188-210A Information for United States Users Appendix D Safety and Regulatory Notices FCC ID N6C-SX10WG Information for Canadian Users IC notice SX-500Declaration of Conformity CE SX-500 Information for European Users SX-500Silex Technology America, Inc Appendix E Silex Contact InformationSilex Technology Europe GmbH Silex Technology Beijing, IncSilex Technology America, Inc