Silex technology SX-500-1402 Chapter Advanced Configuration, Factory Default Settings, Cts/Rts

Page 32

Chapter 5

Advanced Configuration

The Serial Device Server Serial Device Server is equipped with a default configuration that works with most serial-to-Ethernet connections. You can modify the settings to suit your installation requirements.

The web browser interface is the recommended method for setting advanced configuration parameters. However, regardless of the method to access the configuration parameters, the method for modifying the parameters is virtually identical.

Factory Default Settings

Table 3 displays the serial port configuration parameter descriptions and settings with the default settings indicated in a separate column.

Table 3 Factory Default Settings

Parameter

Description

Settings

Default Setting

	Character	Bits per character	7, 8	8

	Flow	Flow control	None, XON, XOFF,	None
			CTS/RTS

	Parity	Parity	None, Even, Odd,	None
			Mark, Space
	Speed	Baud rate of bits per second	300, 600,1200, 2400,
			3600, 4800, 7200,	115200
			9600, 14400,19200,	115200
			9600, 14400,19200,
			38400, 57600, 76800,
			115200, 230400,
			460800, 921600

	Stop	Stop bits per character	1, 2	1

	Ecaddr	ECable destination IP address	Set by user	N/A

	Econn	ECable connection attempt time	1-255 seconds	30 seconds

	Ecport	ECable destination TCP port number	Set by user	N/A

	Eclport	ECable destination local IP port	Set by user	N/A


	Page 26	Silex		Advanced Configuration

Part Number 140-00188-210A

Image 32

Contents

SX-500-1402 Serial Device Server Trademarks Page Contents Figures Contents Silex Part Number 140-00188-210A Emissions Disclaimer Safety PrecautionsAbout This Reference Guide Revision History 2009.08.13 Lee Aydelotte Initial ReleaseIntroduction SX-500Logical Ports Port Name DescriptionLED FIPS-140-2 Interface Physical Logical InterfaceWPA2 AES-CCMP ConfigurationRequired Setting Https Physical Protection Secure OperationInstalling the Serial Device Server Installing the Serial Device Server HardwareVerify Package Contents RS-232 connector pinouts and cabling Monitoring Serial Device Server Status Status Monitors Function StateChapter Configuring the Serial Device Server Basic Configuration RequirementsTCP/IP Settings Wireless Configuration SettingsConfiguration Methods First-Time IP Address Configuration Ping ipaddress Using a Web Browser to Configure the Serial Device Server Silex Authentication Server Certificate You can skip the remainder of this chapter AD-HOC Disabled Init ExitChapter Using the Serial Device Server with Your Application Serial Port Emulator Raw TCP connection Telnet ipaddress portnumberECable Mode RFC 2217 Remote Modem Control SupportPrint Server Mode Console Mode SwitchingAT Commands SET Port S1 Filter ATChapter Advanced Configuration Factory Default SettingsFactory Default Settings Parameter Description CTS/RTSModifying TCP/IP Settings Parameter Description Settings Default SettingDNS Using AT Modem CommandsTCP/IP Settings Parameter Standard AT Commands Supported AT Commands Parameter DescriptionAT#Cset nw ssid silex#Csave Parameter Command DescriptionExtended AT Commands Parameter Description Response Codes Response Codes Numeric Code DescriptionChapter Troubleshooting Email Tech support support@silexamerica.com Radio Performance Specifications Parameter Chapter Product SpecificationsProduct Specifications Component Parameter Specifications TCP Port ConnectionsTCP Port Connections Port Destination DeviceAppendix a Advanced Security Configuration PSKEAP Ttls LeapEncryption Mode Wireless Security Only Key Selection Wireless Security OnlyWEP Key Value Wireless Security Only Pre-Shared Key Wireless Security OnlyWireless Authentication Type Wireless Security Only Wired Authentication Type Wired Ethernet Networks OnlyAuthentication Attempts PasswordProduct Specifications Silex Part Number 140-00188-210A Appendix B Console Commands Wireless and Network Security CommandsNetwork Commands Description Signal Quality Signal Strength = Noise LevelSET NW Ethauth Ttls TLS Peap Command DescriptionTLS PSK SET NW KEY# Wifi RTS Threshold = CL NW BSsidSET NW RTS SET NW CertcnSET NW CERTCN2 SET NW CertexpSET NW Certkey SET NW IDSET NW Realm SET NW Wpagroup Enable DisableSET NW Inap PAPMSCHAPV2 Port Commands SET NW ResetPort Commands Description XON/XOFFServer Information Commands Server Information Commands DescriptionCL Port S1 JOB SET Port S1 Size 7SET SERVEr NAme Name SET Snmp CONtact StringSET Snmp LOCation string SH SerialService Commands Service Commands DescriptionTwcffffff BINARYP1TEXTP1 TWCFFFFFFP14String Commands String CommandsTCP/IP Commands TCP/IP Commands DescriptionEnter LANGUAGE= POSTSCRIPT\0AAll hosts permitted access SET ARP ENable DIsableSET IP BAnner ENable DIsable SET IP Chksum ENable DIsableAuto Bootp Rarp Dhcp Static SET IP FTPSET IP Http SET IP LPDSET IP TCP SET IP TftpXxxxxxS1A 9100 XxxxxxS1B 3001 SH IPAuto Firmware Update Firmware Update Command DescriptionMiscellaneous Commands Description Miscellaneous CommandsHelp Commands Console Commands Silex Part Number 140-00188-210A Appendix C Firmware Update Procedures Firmware Update Procedures Silex Part Number 140-00188-210A Appendix D Safety and Regulatory Notices Information for United States UsersInformation for Canadian Users IC notice SX-500  FCC ID N6C-SX10WGInformation for European Users SX-500 Declaration of Conformity CE SX-500Appendix E Silex Contact Information Silex Technology America, IncSilex Technology Europe GmbH Silex Technology Beijing, IncSilex Technology America, Inc